manualshive.com logo in svg

RIDGID R4120, Operator'S Manual

Share
Download
RIDGID R4120 Operator'S Manual Download Page 28

28

CUTTING COMPOUND MITERS

To aid in making the correct settings, the compound angle setting chart below has been provided. Since compound cuts are 
the most difficult to accurately obtain, trial cuts should be made in scrap material, and much thought and planning made, 
prior to making your required cut.

4

 pitCh

 oF siDe

nuMber oF siDes

0°

6

M- 45.00°
B-    0.00°

5°

10°

15°

20°

25°

30°

35°

40°

45°

50°

55°

60°

65°

70°

75°

80°

85°

90°

5

7

8

9

10

M- 36.00°
B-    0.00°

M- 30.00°
B-   0.00°

M- 25.71°
B-    0.00°

M- 22.50°
B-   0.00°

M- 20.00°
B-    0.00°

M- 18.00°
B-    0.00°

Each B (Bevel) and M (Miter) Setting is Given to the Closest 0.005°.

COMPOUND-ANGLE SETTINGS FOR POPULAR STRUCTURES

M- 44.89°
B-   3.53°

M- 35.90°
B-   2.94°

M- 29.91°
B-   2.50°

M- 25.63°
B-   2.17°

M- 22.42°
B-   1.91°

M- 19.93°
B-   1.71°

M- 17.94°
B-   1.54°

M-   7.82°
B -16.26°

M- 14.51°
B- 43.08°

M- 44.56°
B-   7.05°

M- 35.58°
B-   5.86°

M- 29.62°
B-   4.98°

M- 25.37°
B-   4.32°

M- 22.19°
B-   3.81°

M- 19.72°
B-   3.40°

M- 17.74°
B-   3.08°

M- 44.01°
B- 10.55°
M- 43.22°
B- 14.00°
M- 42.19°
B- 17.39°

M-   4.98°
B- 44.78°
M-   0.00°
B- 45.00°

M-   9.85°
B- 44.14°

M- 18.88°
B- 41.64°

M- 22.91°
B- 39.86°

M- 26.57°
B- 37.76°

M- 29.84°
B- 35.40°

M- 32.73°
B- 32.80°

M- 35.26°
B-  30.00°

M- 37.45°
B- 27.03°

M- 39.32°
B- 23.93°

M- 40.89°
B- 20.70°

M- 35.06°
B-   8.75°

M- 29.15°
B-   7.44°

M- 24.95°
B-   6.45°

M- 21.81°
B-   5.68°

M- 19.37°
B-   5.08°

M- 17.42°
B-   4.59°

M- 34.32°
B- 11.60°

M- 28.48°
B-   9.85°

M- 24.35°
B-   8.53°

M- 21.27°
B-   7.52°

M- 18.88°
B-   6.72°

M- 16.98°
B-   6.07°

M- 33.36°
B- 14.38°

M- 27.62°
B- 12.20°

M- 23.56°
B- 10.57°

M- 20.58°
B-   9.31°

M- 18.26°
B-   8.31°

M- 16.41°
B-   7.50°

M- 32.18°
B- 17.09°

M- 26.57°
B- 14.48°

M- 22.64°
B- 12.53°

M- 19.73°
B- 11.03°

M- 17.50°
B-   9.85°

M- 15.72°
B-   8.89°

M- 30.76°
B- 19.70°

M- 25.31°
B- 16.67°

M- 21.53°
B- 14.41°

M- 18.74°
B- 12.68°

M- 16.60°
B- 11.31°

M- 14.90°
B- 10.21°

M- 29.10°
B- 22.20°

M- 23.86°
B- 18.75°

M- 20.25°
B- 16.19°

M- 17.60°
B- 14.24°

M- 15.58°
B- 12.70°

M- 13.98°
B- 11.46°

M-   0.00°
B- 36.00°

M-   0.00°
B- 30.00°

M-   0.00°
B- 25.71°

M-   0.00°
B- 22.50°

M-   0.00°
B- 20.00°

M-   0.00°
B- 18.00°

M-   3.62°
B- 35.84°

M-   2.88°
B- 29.87°

M-   2.40°
B- 25.61°

M-  2.07°
B- 22.41°

M-  1.82°
B- 19.92°

M-   1.62°
B- 17.93°

M-   7.19°
B- 35.37°

M-   5.73°
B- 29.50°

M-   4.78°
B- 25.30°

M-   4.11°
B- 22.14°

M-   3.62°
B- 19.68°

M-   3.23°
B- 17.72°

M- 10.65°
B- 34.59°

M-   8.50°
B- 28.88°

M-   7.10°
B- 24.78°

M-   6.12°
B- 21.69°

M-   5.38°
B- 19.29°

M-   4.81°
B- 17.37°

M- 13.95°
B- 33.53°

M- 11.17°
B- 28.02°

M-   9.35°
B- 24.06°

M-   8.06°
B- 21.08°

M-   7.10°
B- 18.75°

M-   6.34°
B- 16.88°

M- 17.07°
B- 32.19°

M- 13.71°
B- 26.95°

M- 11.50°
B- 23.16°

M-   9.93°
B- 20.29°

M-   8.74°
B- 18.06°

M- 19.96°
B- 30.60°

M- 16.10°
B- 25.66°

M- 13.54°
B- 22.07°

M- 11.70°
B- 19.35°

M- 10.31°
B- 17.23°

M-   9.23°
B- 15.52°

M- 22.62°
B- 28.78°

M- 18.32°
B- 24.18°

M- 15.44°
B-  20.82°

M- 13.36°
B- 18.27°

M- 11.79°
B- 16.27°

M- 10.56°
B- 14.66°

M- 25.03°
B- 26.76°

M- 20.36°
B- 22.52°

M- 17.20°
B- 19.41°

M- 14.91°
B- 17.05°

M- 13.17°
B- 15.19°

M- 11.80°
B- 13.69°

M- 27.19°
B- 24.56°

M- 22.21°
B- 20.70°

M- 18.80°
B- 17.87°

M- 16.32°
B- 15.70°

M- 14.43°
B- 14.00°

M- 12.94°
B- 12.62°

OPERATION

Summary of Contents for R4120





































Reviews:

No comments

Brands by name

Popular brands

Load more brands