Ricoh SP 200SF Operating Instructions And User Manual Download Page 45

Page: 45 / 192

If a Paper Mismatch Occurs

If the paper size or type does not match the print job's settings, the machine reports an error. There are
two ways to resolve this error:

Continue printing using mismatched paper

Use the form-feed function to ignore the error and print using mismatched paper.

Reset the print job

Cancel printing.

Continuing Printing Using Mismatched Paper

If the paper is too small for the print job, the printed image will be cropped.

If the error message is displayed, press the [

] key.

CTT008

Resetting the Print Job

If the error message is displayed, press the [

] key.

CTT007

If a Paper Mismatch Occurs

Summary of Contents for SP 200SF

































































































































































































Search results

Summary of Contents for SP 200SF

Reviews:

Related manuals for SP 200SF

Brands by name

Popular brands

Ricoh SP 200SF, Operating Instructions And User Manual

Search results

Summary of Contents for SP 200SF

Reviews:

Related manuals for SP 200SF

Brands by name

Popular brands