Ricoh SH-P1 M020 Field Service Manual Download Page 230

Page: 230 / 312

Firmware Update

• Never turn off the machine while downloading the firmware.

Type of Firmware

The table lists the firmware programs used by the machine. All the programs can fit on one SD card.

Program

What It Updates

Engine

Printer engine control

Network DocBox

Document server firmware

Printer

Printer feature applications

System

Printer management

Network Support

Network application

RPCS

RPCS printer device driver

Postscript

Postscript printer device driver

PCL

PCL printer device driver

PDF

PDF printer device driver

PJL

PJL printer device driver

Font

Printer fonts

Web

Web application

SDK1

SDK application

Precautions

Handling SD Cards

Observe these precautions when handling SD cards:

• Always turn off the main power switch before you insert or remove an SD card. Data on an SD

card can be corrupted if you insert or remove an SD card while the main power switch is on.

5. System Maintenance Reference

228

Summary of Contents for SH-P1 M020

























































































































































































































































































































Search results

Summary of Contents for SH-P1 M020

Reviews:

Related manuals for SH-P1 M020

Brands by name

Popular brands

Ricoh SH-P1 M020, Field Service Manual

Search results

Summary of Contents for SH-P1 M020

Reviews:

Related manuals for SH-P1 M020

Brands by name

Popular brands