Ricoh Ri 100 Operating Instructions Manual Download Page 149 | Manualshive

Page: 149 / 260

background image

• 100Mbps Full D.

Default: [Auto Select]

Prmt SNMPv3 Com

Select SNMPv3 communication for managing the machine using MIB.

• Ciphertext
• Cleartext

Default: [Ciphertext]

Pmt SSL/TLS Com

Set SSL/TLS communication under IPv4 and IPv6 to [Active] or [Not Active]. This
communication mode will be used when you specify machine settings using a Web browser.

• Active
• Not Active

Default: [Active]

Restore Default

You can reset the network settings to their defaults.

Wireless LAN

Configure settings for wireless LAN.

SSID

You can display or specify an SSID.

Security Method

You can specify the encryption of the wireless LAN.
Default: [Not Active]

Easy Setup

Select [Easy Setup] to configure the wireless LAN settings automatically. Select either [PBC
Method] or [PIN Method] that is correct to network connection via the access points you can
use.

MAC Address

You can display the wireless LAN's MAC address (physical address).

USB Setting

You can specify the settings related to communication when the computer and machine are
connected via USB. Usually, you do not need to change these settings.
After changing this setting, turn the machine off, and then turn it on again.

USB Speed

• Full Speed

Using the [Host Interface] Menu

147

«
...
147
148
149
150
151
...
»

Summary of Contents for Ri 100





































































































































































































































































Reviews:

No comments

Related manuals for Ri 100

Brand: Dascom Pages: 138

Brand: Dascom Pages: 166

Brand: Datecs Pages: 73

Brand: Datamax Pages: 12

E-Class Mark II

Brand: Datamax Pages: 40

Brand: Datamax Pages: 46

Brand: TallyGenicom Pages: 3

Brand: Xerox Pages: 16

Brand: Xerox Pages: 2

Brand: Xerox Pages: 2

imageRUNNER 4570

Brand: Canon Pages: 154

imageRUNNER ADVANCE DX C478iZ

Brand: Canon Pages: 208

imageRUNNER ADVANCE DX C477iFZ

Brand: Canon Pages: 92

WorkCentre 7655

Brand: Xerox Pages: 24

Brand: Olivetti Pages: 74

Brand: Colorjet Pages: 52

AficioSP C410DN

Brand: Ricoh Pages: 204

Brand: Oki Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands