Ricoh MP C4504 series Start Manual Download Page 12

A-8

 

CAUTION:

• 

If this machine is not going to be used for several days or longer at a time, 
disconnect its power cord from the wall outlet.

• 

Be sure to push the plug of the power cord fully into the wall outlet. Partially 
inserted plugs create an unstable connection that can result in unsafe 
buildup of heat.

• 

When disconnecting the power cord from the wall outlet, always pull the 
plug, not the cord. Pulling the cord can damage the power cord. Use of 
damaged power cords could result in fire or electric shock.

• 

Be sure to disconnect the plug from the wall outlet and clean the prongs 
and the area around the prongs at least once a year. Allowing dust to build 
up on the plug constitutes a fire hazard.

• 

When performing maintenance on the machine, always disconnect the 
power cord from the wall outlet.

Power Source
100-240 V, 3 A, 50/60 Hz
Please be sure to connect the power cord to a power source as above.

Handling the main machine

This section explains safety precautions about handling the main machine.

 

WARNING:

• 

The following explains the warning messages on the plastic bag used 
in this product’s packaging.

• 

 Keep the polythene materials (bags, etc.) supplied with this 
machine away from babies and small children at all times. 
Suffocation can result if polythene materials are brought into 
contact with the mouth or nose.

• 

If the machine topples, or if a cover or other part gets broken, you 
must turn off its power immediately. After turning off the power, be 
sure to disconnect the power cord plug from the wall outlet. Then 
contact your service representative and report the problem. Do not 
use the machine. Doing so could result in fire or electric shock.

Summary of Contents for MP C4504 series

























Reviews: