Ricoh LP124w Page 193 Software Manual Download | Manualshive

Page: 193 / 376

background image

Printable TIFF Files

179

5

Printable TIFF Files

TIFF Data Specifications

TIFF files that can be processed

This section explains the TIFF filter's file processing limitations. The TIFF filter
can process only TIFF files that are compliant with “TIFF Revision 6.0” (Adobe
Developers Association, June 1992).

Note

❒

The TIFF filter might be able to process non-compliant TIFF files, but the out-
put is likely to be incorrect, depending on the size of the image.

TIFF header

TIFF data requires the header values shown in the table below.

TIFF directory

If the data is multi-page TIFF:
• Both the directory and data must be divided by page.
• The last four bytes of each directory must contain a pointer to the subsequent

page, and the pointer value must increase in keeping with the page order.

Note

❒

The pointer value for both single page TIFF data and the last page of multi-
page TIFF data must be “0x00000000”.

• The page order must be the same as the intended output order.

Field

Values

Byte order

0x4d4d or 0x4949

Version number

42

«
...
191
192
193
194
195
...
»

Summary of Contents for LP124w

























































































































































































































































































































































































Reviews:

No comments

Related manuals for LP124w

Magicolor 2 Desklaser

Brand: QMS Pages: 60

Brand: Partner Pages: 34

Digital Color Press 700

Brand: Xerox Pages: 216

Brand: Riso Pages: 208

IMAGE M4100 Series

Brand: G&G Pages: 147

Brand: Oki Pages: 20

ColorPainter M-64S

Brand: Oki Pages: 84

Brand: BIXOLON Pages: 20

Brand: Lexmark Pages: 60

Brand: Konica Minolta Pages: 165

Brand: Nashuatec Pages: 177

Brand: Epson Pages: 105

Brand: Epson Pages: 128

Brand: Epson Pages: 145

Brand: Epson Pages: 200

Brand: Epson Pages: 2

Brand: WOOSIM Pages: 27

Brand: ALZA Pages: 109

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands