Quick Installation Guide
Unpacking
To protect it from shock and vibration during transit,
this printer comes packaged in cushioning foam and
secured with tape. Remove these protective materials
after bringing the machine to where it will be installed.
Caution
•
When moving the machine, hold the handles at
both sides, and then lift the printer slowly. Lifting
it carelessly or dropping it may cause an injury.
•
Place no objects on the front or inner cover.
Pull out the handle from the right side of
the printer.
BMV016S
Lift the printer with four people by using
the handles on both sides of the printer.
BEJ126S
•
Leave the tape in place while moving the printer.
•
Lower the printer slowly and carefully to prevent
trapping your hands.
Return the handle you pulled out from
the printer to its original position.
Remove the tape indicated by the arrow.
Do not remove the four strips of tape
attached to the front cover.
BMV291S
Read this manual carefully before you use the product and keep it handy for future reference.
For safe and correct use, please be sure to read “
Safety Information
” before using the
machine.
❖
Optimum Environmental Conditions
Permissible and recommended temperature and hu-
midity ranges are as follows:
BEK339S
BEK258S
•
White area: Permissible Range
•
Gray area: Recommended Range
•
The machine must be level within 5 mm, 0.2˝ from
both front to rear and left to right.
•
To avoid possible build-up of ozone, locate this ma-
chine in a large well ventilated room that has an air
turnover of more than 30 m
3
/hr/person.
•
When you use this machine for a long time in a con-
fined space without good ventilation, you may de-
tect a smell. To keep the workplace comfortable, we
recommend that you keep it well ventilated.
❖
Power Source
Connect the power cord to a power source of the fol-
lowing specification:
•
120 V, 60 Hz, 12 A or more
Where to Put the Printer
The printer’s location should be carefully chosen because
environmental conditions greatly affect its performance.
Warning
•
The supplied power cord is for use with this
equipment only. Do not use with other appliances.
Doing so may result in fire, electric shock, or injury.
•
Connect the machine to the power source specified in
"
Safety Information
" and do not use any other
power sources. Connect the power cord directly to a
wall outlet and do not use an extension cord. Power
sources not specified in "
Safety Information
" and
extension cords are electric shock or fire hazards.
•
Power cords that are damaged, broken, modified,
trapped under heavy objects, pulled hard, or bent
severely are electric shock and fire hazards.
Caution
•
Make sure the room where you are using the machine
is well ventilated and spacious. Good ventilation is
especially important when the machine is used heavily.
•
Place the machine on a strong and level surface.
Otherwise, it might fall and injure somcaeone.
•
Keep the machine in an area that is within
optimum environmental conditions.
Operating the machine in an environment that is
outside the recommended ranges of humidity and
temperature can cause an electrical fire hazard. Keep
the area around the socket free of dust. Accumulated
dust can become an electrical fire hazard.
•
It is dangerous to handle the plug with wet hands.
Doing this may result in receiving an electric shock.
Do not use the printer in the following environments:
•
Areas exposed to direct sunlight or strong light
•
Dusty areas
•
Areas with corrosive gases
•
Areas that are excessively cold, hot, or humid
•
Locations near air conditioners or humidifiers
•
Locations near other electronic equipment
•
Locations subject to frequent strong vibration
❖
Space Required for Installation
Leave enough space around the printer to operate it
freely. The recommended minimum space is as follows:
BEK280S
: 75.0 cm (29.6 inches) or more
: 10.0 cm (4.0 inches) or more
: 10.0 cm (4.0 inches) or more
: 55.0 cm (21.7 inches) or more
: 67.0 cm (26.4 inches) or more
: 67.0 cm (26.4 inches) or more
Holding the left and right side grips,
carefully open the front cover.
BMV060S
Turn the two green levers counterclock-
wise.
BUA002S
Pulling the handle, slowly open the inner
cover.
BUA003S
Remove the orange tapes from the
printer.
BMV308S
Pull out the tapes horizontally. Be sure
to pull out all four strips of tape.
BMV309S
•
To avoid malfunctions, be sure to remove all four
strips of tape from the photo conductor unit.
•
Removed tape is dirty. Be careful not to let it touch
your hands or clothes.
Pressing both sides, firmly close the
inner cover.
BUA004S
Turn the two green levers clockwise to
lock the cover.
BUA005S
Checking the Included Items
Verify the items that come with the printer. Make sure
that you find all the items listed below.
Note that some of the items are in tray 1. Pull out tray
1, and remove the red tag on the tray. Take out the
items inside tray 1.
BMV260S
❖
Manuals and CD-ROMs
Quick Installation Guide (This manual)
CD-ROM “Printer Drivers and Utilities”
Safety Information
CD-ROM “Manuals”
CD-ROM “Document Management Utility”
Ferrite Core
ATU602S
Power cord
Toner: Black (K), Magenta (M), Cyan (C),
Yellow (Y)
ASZ601S
Color Calibration Sample Sheet
Additional Documentation
Paper Feed Unit Labels
•
This package does not include an interface cable.
Purchase one as necessary to connect to the printer.
CLP340D/CLP350D/C8140ND/C8150ND/
LP540C/LP550C/Aficio SP C820DN/SP C821DN
