manualshive.com logo in svg

Ricoh Aficio MP 2500, Facsimile Reference Manual

The Ricoh Aficio MP 2500 is a powerful multifunctional printer that combines printing, copying, and scanning capabilities. With its network manual, users can easily set up and configure the printer to their network. Download the free manual from our website to maximize the functionality of this exceptional product.

Share
Download
background image

Reception

118

3

Memory Reception

The machine waits until all pages of the document have been received into mem-
ory before printing it.

Important

❒

About twelve hours after the machine is turned off, all fax documents stored
in memory are lost. If any documents are lost in this way, a Power Failure Re-
port is automatically printed when the operation switch is turned on. Use this
report to identify lost documents. See “Troubleshooting When Using the Fac-
simile Function”, Troubleshooting.

❒

The machine may not be able to receive fax documents when free memory
space is low.

❒

If free memory reaches 0% during Memory Reception, any further reception
becomes impossible and the current communication is terminated.

Reference

“Troubleshooting When Using the Facsimile Function”, Troubleshooting

Summary of Contents for Aficio MP 2500













































































































































































































Reviews:

No comments

Related manuals for Aficio MP 2500

Olympus P-10 Instruction preview
P-10
Brand: Olympus Pages: 2
Samsung Xpress M2020W User Manual preview
Xpress M2020W
Brand: Samsung Pages: 199
Canon PIXMA TR4720 Online Manual preview
PIXMA TR4720
Brand: Canon Pages: 542
Citizen PPU-231 User Manual preview
PPU-231
Brand: Citizen Pages: 75
InfoSight LabeLase LL2800 Basic Operations & Maintenance Manual preview
LabeLase LL2800
Brand: InfoSight Pages: 24
Panasonic DP-3530 Service Manual preview
DP-3530
Brand: Panasonic Pages: 858
Samsung ML-1640 Series Specifications preview
ML-1640 Series
Brand: Samsung Pages: 2
Samsung ML-1600 Series Service Manual preview
ML-1600 Series
Brand: Samsung Pages: 13
Samsung ML-1630W/SEE Service Manual preview
ML-1630W/SEE
Brand: Samsung Pages: 37
Samsung CLX-6260ND/SEE Specification preview
CLX-6260ND/SEE
Brand: Samsung Pages: 2
Samsung CLX-4195 Series Service Manual preview
CLX-4195 Series
Brand: Samsung Pages: 20
Samsung CLP-415NW Specifications preview
CLP-415NW
Brand: Samsung Pages: 2
Samsung CLP-365W Specifications preview
CLP-365W
Brand: Samsung Pages: 2
Samsung CLP-36 Series Quick Installation Manual preview
CLP-36 Series
Brand: Samsung Pages: 2
Samsung CLP-300 Remanufacturing Instructions preview
CLP-300
Brand: Samsung Pages: 5
Samsung ML-1640 Series User Manual preview
ML-1640 Series
Brand: Samsung Pages: 83
Samsung CLP-36 W Series User Manual preview
CLP-36 W Series
Brand: Samsung Pages: 50
Samsung ML-1610 Series User Manual preview
ML-1610 Series
Brand: Samsung Pages: 110

Brands by name

Popular brands

Load more brands