Ricoh Aficio MP 2000L Scanner Reference Download Page 108

Page: 108 / 134

Various Scan Settings

102

Press the

{

Escape

}

key.

Note

❒

To set originals of the same width and different length at the same time, set
them according to the chart below.

❒

The following combinations of original sizes are available: A3

&A4

&B5

and A4

&A5

Stamp

This section explains the procedure for stamping on originals scanned using the
ADF/ARDF.
If you select

[

Stamp

]

, a circle mark is stamped on originals that are scanned using

the ADF/ARDF. If you scan a two-sided original using the ARDF, circle marks
are stamped on both sides of the original.
This function is useful when you want to identify scanned originals.

This illustration is an example when scanning a two-sided original.

Important

❒

To enable stamping, you must install the stamp cartridge.

ALO033S

ARO006S

Summary of Contents for Aficio MP 2000L







































































































































Search results

Summary of Contents for Aficio MP 2000L

Reviews:

Related manuals for Aficio MP 2000L

Brands by name

Popular brands

Ricoh Aficio MP 2000L, Scanner Reference

Search results

Summary of Contents for Aficio MP 2000L

Reviews:

Related manuals for Aficio MP 2000L

Brands by name

Popular brands