Ricoh Aficio IS 2425 Operating Instructions Manual Download Page 258

Page: 258 / 288

Registering Addresses and Users for Facsimile/Scanner Functions

250

Changing the E-mail Transfer Station

This section describes how to change the E-mail Transfer Station.

Press

[

E-mail

]

Change the Transfer Station's information. See step

and

"Changing a

Registered E-mail Destination".

Reference

p.213 “Changing an E-mail Destination”

Changing the Receiving Station

This section describes how to change the Receiving Station.

Press

[

Receiving Statn.

]

Select the Receiving Station you want to change.

Press

[

Clear

]

to clear the number, and then enter the new number using the

number keys.

Deleting a Transfer Station / Receiving Station

This section describes how to delete the Transfer Station / Receiving Station.

Press

[

System Settings

]

Press

[

Administrator Tools

]

Press

[

Next

]

Press

[

Address Book: Program / Change / Delete Transfer Request

]

Press

[

Delete

]

Select the name whose Transfer Station / Receiving Station you want to delete.

Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.

Press

[

Yes

]

Press

[

Exit

]

Note

❒

To delete the name, key display, and title, see “Deleting a Registered Name”.

Reference

p.189 “Deleting a Registered Name”

Summary of Contents for Aficio IS 2425

































































































































































































































































































Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands

Ricoh Aficio IS 2425, Operating Instructions Manual

Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands