Ricoh Aficio IS 2325 Operating & Troubleshooting Instructions Download Page 107 | Manualshive

Page: 107 / 126

background image

Adding Toner

99

7

Note

❒

Do not remove the black cap before shaking.

❒

Do not remove the inner cap.

Sending Fax Messages When Toner Has Run Out

When the machine has run out of toner, the indicator on the display lights. Note
that even if there is no toner left, you can still send fax documents.

Important

❒

Communication is not possible if the number of communications executed af-
ter the toner has run out plus the number of communications not listed in the
journal exceeds 200.

A

Make sure that the machine is in facsimile mode.

If the fax screen does not appear, press the

{

Facsimile

}

key.

B

Press

[

Exit

]

, and then perform transmission operation.

The error message disappears.

Note

❒

The communication results report cannot be printed.

Waste Toner

Waste toner cannot be re-used.
Take the bottle of waste toner to your sales representative or service representa-
tive for recycling. If you dispose of it on your own, treat it as general plastic
waste.

«
...
105
106
107
108
109
...
»

Summary of Contents for Aficio IS 2325































































































































Reviews:

No comments

Related manuals for Aficio IS 2325

Brand: Olympus Pages: 71

Brand: EBS Pages: 4

Brand: NCR Pages: 38

Brand: Panasonic Pages: 102

Brand: QMS Pages: 311

Brand: Xerox Pages: 5

Aficio MP C6503SP

Brand: Ricoh Pages: 264

Brand: Oki Pages: 2

Brand: VuPoint Pages: 20

Brand: Konica Minolta Pages: 404

Brand: Savin Pages: 4

Brand: Star Micronics Pages: 194

Phaser 3100MFP/S

Brand: Xerox Pages: 56

Brand: Citizen Pages: 44

Brand: Olivetti Pages: 56

Brand: QMS Pages: 188

Brand: Sinfonia Technology Pages: 41

Brand: Sharp Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands