Ricoh 161 Function Manual Download Page 28 | Manualshive

Page: 28 / 192

background image

Transmission

20

1

Dual Access

The machine can scan other documents into memory even while sending a fax
document from memory, receiving a document into memory, or automatically
printing a report. Since the machine starts sending the second document imme-
diately after the current transmission ends, the line is used efficiently.

Note

❒

During Immediate Transmission or when in User Tools mode, the machine
cannot scan an original.

Simultaneous Broadcast

Use this function to send the same original to multiple destinations simultaneously.
To specify multiple destinations, specify the first destination, and then specify
the next destination by pressing

[

Add Dest

]

.

If you dial several destinations for the same document (broadcasting), the docu-
ments are sent in the order in which they were dialed. If the fax document could
not be transmitted, the machine redials that destination after the last destination
specified for broadcasting. For example, if you specify four destinations, A
through D, for broadcasting, and if the lines to destinations A and C are busy,
the machine dials the destinations in the following order: A, B, C, D, A, and C.
To check the transmission progress, print the TX file list.
If you specify a second transmission while broadcasting to several destinations,
faxes are transmitted alternately to each remaining destination in the current
and second broadcast.
For example, if you specify a broadcast to destinations A and B, and then specify
a broadcast to destinations C and D while transmission to destination A is in
progress, the machine sends the faxes in the following order: A, C, B, and then D.
If the previous file and next file are both on standby, these are also sent in the
same order.

Note

❒

To avoid accidentally pressing the wrong Quick Dial key, you can set the ma-
chine so that each time a destination is added using a Quick Dial key,

[

Add

Dest

]

must be pressed. Make the setting in User Parameters (switch 17, bit 2)

in the Fax Features menu.

Reference

p.129 “Printing a List of Files in Memory (Print TX Standby File List)”
“Fax Features”, General Settings Guide

«
...
26
27
28
29
30
...
»

Summary of Contents for 161

































































































































































































Reviews:

No comments

Related manuals for 161

Brand: Xerox Pages: 168

Brand: Xerox Pages: 36

Brand: Xerox Pages: 64

Brand: Xerox Pages: 54

Brand: Xerox Pages: 2

Brand: Xerox Pages: 115

Brand: Fenix Imvico Pages: 88

DocuCentre SC2020

Brand: Xerox Pages: 322

Brand: Xerox Pages: 2

Brand: Xerox Pages: 8

Brand: Xerox Pages: 80

Brand: Xerox Pages: 38

WorkCentre 7132

Brand: Xerox Pages: 73

7400DT - Phaser Color LED Printer

Brand: Xerox Pages: 20

WorkCentre 7655

Brand: Xerox Pages: 24

Brand: Lanier Pages: 6

Brand: A&D Pages: 24

Brand: Gainscha Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands