background image

Model KS10013 

Photographs are not to scale. 
Specifications subject to change 
without prior notice. 

0359 

 
 
 
 
 

 

WARNING

 

• 

For outdoor use only. Not for commercial use.

 

• 

Use only Propane regulator 37mbar.

 

• 

Read instructions before using the appliance. Failure to follow instructions could 
result in death, serious bodily injury, and/or property loss.

 

• 

Warning: accessible parts may be very hot. Keep young children away.

 

• 

Do not move the appliance during use.

 

• 

Turn off the gas supply at the gas bottle after use.

 

• 

Any modification of the appliance, misuse, or failure to follow the instructions may 
be dangerous and will invalidate your warranty. This does not affect your statutory 
rights.

 

• 

Retain these instructions for future reference.

 

• 

Leak test your barbecue annually. Check the hose connections are tight and leak 
test them each time you reconnect the gas bottle. 

FOR YOUR SAFETY 

 

If you smell gas: 
1. 

Shut off gas to the appliance. 

2. 

Extinguish any open flame. 

3. 

Open barbecue lid or hood. 

4. 

If odour continues, discontinue use and 
contact your local dealer. 

FOR YOUR SAFETY 

 

1. 

Do not store or use petrol or other flammable 
vapours or liquids in the vicinity of this or any 
other appliance. 

2. 

A gas bottle not connected for use shall not be 
stored in the vicinity of this or any other 
appliance. 

 

Assembly and Operating Instructions for 

 

3 Burner with Side Burner Gas BBQ 

PDF created with pdfFactory trial version 

www.pdffactory.com

Summary of Contents for KS10013





















Reviews: