Note
Lower Gate Lock
Lower
Gate Lock
Upper Gate Lock
Upper
Gate Lock
Lower
Gate Lock
Upper
Gate Lock
15.5 Ibs (7.0 kg)
Figure 8
l
Make sure each space between Main Frame and
Upper/Lower Gate Lock is evenly placed so that
the tension spring effect works properly.
l
Place the product against sturdy wall surfaces
(locate studs) to prevent damage to the wall surface.
l
Make sure sides of body are parallel to the wall (Fig. 7).
l
Be sure to install the product correctly to ensure the Gate
Door locks securely.
l
The bottom of product should make contact on the floor
(Fig. 1).
l
If correctly installed, the product should not feel loose or
wobbly when tugged.
l
Make sure both Upper and Lower Gate Locks are locked
when the Gate Door is closed.
l
Grip and lift the Upper Gate Lock so that the Gate Door is
opened by releasing Upper and Lower Gate Locks (Fig. 8).
l
The product is designed to lock automatically when closed.
If too much or too little force is used when closing, the Gate
Door may not lock.
l
Use mild detergent and water, and clean with soft cloth
or sponge. Do not use scrub brush or abrasive scouring
materials.
l
Do not use disinfectant such as cresol.
l
Never use harsh chemicals such as thinner, benzin or
alcohol.
l
After cleaning, do not dry the product in direct sunlight.
Place in shade to dry.
Rotate Adjuster Knobs counterclockwise and loosen
Adjuster Bolts.
Note
l
Be careful not to drop the product when removing.
l
Be sure the Gate Door is locked when removing.
Item Name
Item Size
Easy-Lock Pet Gate
28.3-35.4" x 2" x 31.5" (72-90 x 5 x 80 cm)
Weight
Material
Main/Side Frames: Steel (powder coating)
Gate Door: Rubberwood (lacquer finished)
Resin part: Polypropylene, Polyacetal
Adjuster Knob: Polypropylene
Adjuster Bolt metal part: Steel
Adjuster Bolt rubber part: TPE
0701
Figure 1
Upper Adjuster Knob
Lower Adjuster Knob
Adjust
temporarily
Adjust
temporarily
Adjust
temporarily
Adjust
temporarily
Figure 2
Figure 3
Figure 4
Figure 5
At right angle
with floor
At right angle
with floor
At right angle
with wall
Main Frame
Main Frame
1.8” (4.5 cm) and under
Main Frame
0.04-0.08” (1-2 mm)
0.08-0.12” (2-3 mm)
Figure 6
Figure 7
Sides of body should
be parallel to the wall.
Upper knob not
tightened enough.
Upper knob tightened
too much.
Sides of body should always
be parallel to wall.
①
Determine the direction for opening the Gate Door and
prepare the product for mounting by tightening the Upper
Adjuster Knobs temporarily (Fig. 1).
②
Set the product against the wall (Fig. 2).
③
Tighten the Lower Adjuster Knobs until the clearance
between the Gate Door and the Main Frame is set to
1.8" (4.5 cm) and under as shown in Fig. 3.
④
Make sure the Main Frame remains vertical to the wall.
⑤
Tighten the Upper Adjuster Knob on side of gate
opposite to Upper Gate Lock until the space between
the Main Frame and the Lower Gate Lock is 0.08-0.12"
(2-3 mm) (Fig. 4).
⑥
Tighten the Upper Adjuster Knob on side of Upper
Gate Lock until the space between Main Frame and
Upper Gate Lock is 0.04-0.08"(1-2 mm) (Fig. 5).
⑦
Make sure the sides of body are parallel to the wall
(Fig. 6).
⑧
Make sure the clearance between each part is set
properly and the Adjuster Knob is tightened securely.
Right angle
Right angle
2100 N. Hwy. 360, Suite 1700, Grand Prairie, TX 75050
Designed by :
Richell Corporation, Japan
How to install
7 .
Installation Check / How to open and close the Gate Door
8 .
How to remove
9 .
How to clean
10.
Specifications
11.
3
4
2.4" (6 cm)
and above
Less than
2.4" (6 cm)
