RichAuto AutoNow B18 User Manual Download Page 10

Page: 10 / 75

北京锐志天宏科技股份有限公司

Beijing RichAuto S&T Co., Ltd.

Forging ahead, create future together!

1.2.2

Wiring board

The connection between handle and machine tool rely on the wiring board. As shown

below,

Wiring Board

50-pin cable socket

：

Be used for connecting the metal end of the 50-pin cable.

Output terminal

：

Including Spindle On/Off, Run lamp, Alarm lamp output signal ports etc.

Input terminal

：

Including machine HOME switch, tool setter, driver alarm, hard limit, E-stop

signal, foot pedal switch input signal ports.

Power supply terminal

：

DC 24V, 3A.

Motor driver control terminals: Contains X, Y, Z axis motor drivers output ports.

1.2.3

Board installation dimensions

Scale 1:1, unit mm

50-PIN cable socket

OUTPUT Terminal

J8: INPUT Terminal

J10

Power Supply

24V DC

Motor
driver
control
terminals

X axis

Y axis

Z axis

C axis

Summary of Contents for AutoNow B18












































































Search results

Summary of Contents for AutoNow B18

Reviews:

Related manuals for AutoNow B18

Brands by name

Popular brands

RichAuto AutoNow B18, User Manual

Search results

Summary of Contents for AutoNow B18

Reviews:

Related manuals for AutoNow B18

Brands by name

Popular brands