Rice Lake ELS Series Installation Manual Download Page 20

Page: 20 / 30

Elevated Load Cell Stands

Visit our website

www.RiceLake.com

5. Wind each loose load cell cable to securely fit under the weigh stand channel.
6. Put the wound load cell cables under each weigh stand channel.
7. Attach the wound load cell cables to the weigh stand channel using the provided zip ties.

The wound load cell cables need to lay flat underneath the weigh stand channel.

Figure 2-16. Securing the Load Cell Cable

8. Tighten the load cell cable mounting clamps.

2.12.1 Junction Box Expansion

It is possible to use this junction box with other combinations. Use the expansion port on the main board to connect multiple

junction boxes in a series to accommodate more than two ELS weigh stands. Contact Rice Lake Weighing Systems for

additional details on applications involving more than two weigh stands.

Figure 2-17. Junction Box Expansion Board Location

Note

Wound Load Cell Cable

JPPP

PT4

JP3

JP2

PT1

PT2

-EX

-SI

SHD

+SI

+EX

-SI

+SI

+EX

-EX

-SI

SHD

+SI

+EX

-EX

-SI

SHD

+SI

-SI

-EX

SHD

-EX

SHD

+EX

+SE

-SE

+EX

EXP

-SI

+SI

-EX

SHD

+EX

+SE

-SE

Junction Box Expansion Location

Summary of Contents for ELS Series































Search results

Summary of Contents for ELS Series

Reviews:

Related manuals for ELS Series

Brands by name

Popular brands

Rice Lake ELS Series, Installation Manual

Search results

Summary of Contents for ELS Series

Reviews:

Related manuals for ELS Series

Brands by name

Popular brands