Rice Lake DIGI DS-520 Operation Manual Download Page 8

Page: 8 / 14

4.0.

DS-520 OPERATIONAL PROCEDURES

4.1. Power On/Off

1. Press [ON/OFF] key to turn on the scale.

The display will briefly show all segments, then blank for a second, then go into weighing mode.

2. Press [ON/OFF] key to turn off the scale.

4.2. Automatic Shut Off Timer Setting

1. Begin with the scale turned off.

2. Press and hold the [ON/OFF] key for 3 seconds. This sets the Timer for 3 minutes.

3. Release the [ON/OFF] key when the display shows the number 3. The display will then briefly

show all segments, then blank for a second, then go into weighing mode.

1. Begin with the scale turned off.

2. Press and hold the [ON/OFF] key for 6 seconds. This sets the Timer for 10 minutes.

3. Release the [ON/OFF] key when the display shows the number 6. The display will then briefly

show all segments, then blank for a second, then go into weighing mode.

1. Begin with the scale turned off.

2. Press and hold the [ON/OFF] key for 9 seconds. This sets the Timer for no auto shut off.

3. Release the [ON/OFF] key when the display shows the number 999. The display will then

briefly show all segments, then blank for a second, then go into weighing mode.

Summary of Contents for DIGI DS-520














