Operation Section 4-4
Breeze 08-01
© 2004
Alamo Group Inc.
OPERATION
OPERA
TION
To commence operation, reduce engine speed and engage the tractor PTO. Before starting to cut, gradually
increase engine speed to develop full PTO speed.
Enter the area to cut with the cutter operating at PTO speed and, if it becomes necessary to temporarily regulate
engine speed during operations, increase or decrease the throttle gradually.
To transport, disengage the PTO, raise full transport height.
CUTTING SPEED
Proper ground speed for cutting will depend upon the height, type, and density of material to be cut.
Normally, ground speed will range from 1-1/2 to 3 mph. Tall dense material should be cut at low speed while thin
medium height material can be cut at a faster ground speed.
CUTTING TIPS
Always operate PTO at recommended RPM when cutting. This is necessary to maintain proper blade speed and
to produce a clean cut.
Under certain conditions, tractor tires may roll some grasses down and prevent them from being cut at the same
height as the surrounding area. When this occurs, reduce the tractor ground speed, but maintain PTO RPM. The
lower speed will permit grasses to be at least partially rebound and be cut. Taking a partial cut and/or reversing
the direction of travel may also produce a cleaner cut.
As often as possible, stop mowing when other people are passing by. Although the Mower is shielded to prevent
objects from being thrown out by the blades, no one shield device is 100% effective. The operator has greater
knowledge of the dangers of being around this Mower while it is operational than the person on the street.
WARNING!
Avoid personal injury. Pick up all rocks and other debris
before cutting. Enter new areas carefully. Cut material
higher the first time to allow cutter to clear unseen objects.
Never assume an area is clear. Always check.
Extremely tall grass should be cut twice. Raise cutter and cut twice the
desired height. Cut the second time at desired height at 90 degrees to first
pass.
Remember, sharp blades produce cleaner cuts and use less power.
Before cutting, analyze the area to determine the best cutting procedure.
Consider the height and type of material and the terrain type: hilly, level or
rough.
Grass is best cut when it is dry. Mowing wet grass can cause plugging
resulting in grass clumps behind the mower.
Grass should be mowed frequently as shorter clippings deteriorate faster.
The grass is discharged
to the rear and slightly to the right. To keep
clippings of to streets and sidewalks mow two to three passes clockwise as
shown in
Figure 1.
FIGURE 1
R 03-06-00
Summary of Contents for 48-inch
