Rheem Solar Premier Loline Owner'S Manual Download Page 30 | Manualshive

Page: 30 / 60

background image

INSTALLATION – SOLAR COLLECTORS

30

Maximum Height To Collectors

The solar collectors must be the highest point of the system. The maximum height  of the solar  installation,
from the base of the solar storage tank to the top of the solar collectors, is 9 m. The pump supplied with the
solar storage tank will not circulate closed circuit fluid through heights greater than 9 m and solar gain will not
be achieved.

For heights greater than 9 m, an auxiliary pump  (kit PN 299914) must be installed above and  within 1 m of
the  solar  storage  tank.  The  installation  of  an  auxiliary  pump  will  enable  a  maximum  height  of  18 m  to  be
achieved. Refer to

“Auxiliary Pump”

on page 40.

Note

: The top of the solar storage tank must be a minimum of 500 mm below the bottom of the solar

collectors for the system to operate correctly.

Closed Circuit Drain Back Solar Pipe Work Installation Requirements

«
...
28
29
30
31
32
...
»

Summary of Contents for Solar Premier Loline





























































Reviews:

No comments

Related manuals for Solar Premier Loline

Brand: Hamilton Beach Pages: 15

Brand: A.O. Smith Pages: 24

Brand: A.O. Smith Pages: 62

Brand: Sentiotec Pages: 72

nXDS10i nXDS15i

Brand: Edwards Pages: 58

Brand: RADtec Pages: 7

Brand: IceManCooler Pages: 2

Brand: pyromaster Pages: 20

Brand: Ballu-Biemmedue Pages: 29

Brand: T.I.P. Pages: 117

Brand: Stanley Pages: 4

Brand: Backyard Pro Pages: 18

Brand: Annovi Reverberi Pages: 100

Scalekleen EV9796-01

Brand: Everpure Pages: 2

Brand: FLOJET Pages: 4

Pro VSPHP270JEP

Brand: Jandy Pages: 20

ARO 66605J- Series

Brand: Ingersoll-Rand Pages: 8

Quick-Fill 58609

Brand: Intex Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands