Rheem Solar Hiline 52D180 Owner'S Manual And Installation Instructions Download Page 39 | Manualshive

Page: 39 / 56

Rheem Solar Hiline 52D180 Owner'S Manual And Installation Instructions Download Page 39

SYSTEM ASSEMBLY

39

Clamping Collector To Collector Rail

Refer to

exploded view diagrams

on pages 30

31 for

position and to

1.

Position the collector clamp (16) over the hole in the
collector rail (6) with the top lip of the clamp (16) over
the collector trim.

2.

Insert  the  hex  screw  (14)  through  the  hole  in  the
collector  clamp  (16)  and  collector  rail  (6),  place  the
washer  (36)  and  nut  (15)  on  the  hex  screw  (14)  and
screw the nut (15) until it seats firmly against the lip of
the collector rail (6), applying medium pressure with a
spanner to tighten.

Hooking Roof Strap to Tank Clamp

1.

The  tank  clamp  (5)  is  supplied  as  a  single
extruded  part  and  must  be  snapped  into  two.
Snap  by  bending  the  clamp  on  the  groove
location.

2.

Noting the orientation of the roof

strap’s folded

end, slide the short end of the roof strap (4)
through the slot from the underside of the tank
clamp (5).

3.

Push the roof strap (4) end through the tank
clamp (5) and make sure it is correctly orientated
as illustrated.

4.

Loosely pre-assemble the hex screw (14),
washer (36) and nut (15) as shown. Ensure the
hex screw head fits into the valley of the tile or
roof sheet profile.

Tank Rail Fixing

Tank Clamp Assembly

DETAIL C

DETAIL B

Collector Rail Collector Clamp Installation

209124

209118

204600

collector rail

209130

331842

nut (15)

washer (36)

tank clamp (5)

roof strap (4)

washer (36)

hex screw (14)

nut (5)

washer (36)

clamp (5)

strap (4)

washer (36)

hex screw

(14)

«
...
37
38
39
40
41
...
»

Summary of Contents for Solar Hiline 52D180

























































Reviews:

No comments