Rheem Multipak MPE02 Owner'S Manual And Installation Instructions Download Page 55

Page: 55 / 60

COMMISSIONING

MULTIPAK – FAULT FINDING PROCEDURE

Fault

Possible
Causes

Description & Recommended Corrective Action

No Hot
Water

Gas
Failure

•

Check gas supply and reinstate

Power
Failure

•

Check and reinstate Power Supplies to all the power outlets.

Water
Supply
Failure

•

Check adequate cold water supply is available to all CFWH & no
valves are shut.

•

Check for minimum 140KPa water supply pressure available.

•

Check CFWH strainers for cleanliness

RECFWH
Fault

•

Refer to Rheem Owner’s Guide and Installation Instructions for
additional Information

Long delay
for Hot water
Supply

Optional
Pump
Fault

•

Check pump operation (if fitted) as per commissioning list - item
8

•

(Page 46) of this manual.

•

Check Pump installation has been completed in accordance to
technical notes on page 18 of this manual

MULTIPAK – CFWH STRAINER CLEANING

Isolate the CFWH cold and hot water valves.

Remove the strainer assembly. Clean and refit.

Re-instate the CFWH cold and hot water valves to open position.

Complete above procedure for all the CFWH of the Multipak

Strainer

Natural Gas /

Propane Feed

Cold Water

Feed

Hot Water

Outlet

Summary of Contents for Multipak MPE02





























































Search results

Summary of Contents for Multipak MPE02

Reviews:

Brands by name

Popular brands

Rheem Multipak MPE02, Owner'S Manual And Installation Instructions

Search results

Summary of Contents for Multipak MPE02

Reviews:

Brands by name

Popular brands