WARNING: STRANGULATION HAZARD
Keep cord at least 3 feet away from cribs, bassinets, and toddler beds.
Keep out of reach of children under 3 years of age.
PARTS ENCLOSED:
(A) Ground Wire Screw (1)
(H) Back Plate (1)
(B) Mounting Plate (1)
(I) LED Bulb (1)
(C) Mounting Plate Screws (2)
(J) Arm Knob (1)
(D) Thread Plug Screw (1)
(K) Shade Joint (1)
(E) ON/OFF Rotating Switch (1) (L) Arm Handle (1)
(F) Plate Screws (4)
(G) Plastic Wire Connectors (3)
TEXTURED METAL SWING-ARM SCONCE
Direct-Wire Installation
IMPORTANT SAFETY INSTRUCTIONS:
The fixture can be used as a plug-in or a fixed unit when used with the appropriate
conversion kit. For your safety, this sconce is equipped with a 3-pronged polarized
plug. If the plug does not fit securely into your outlet, do not force it – contact a
professional electrician. Use the plug with an extension cord only if it can be fully
inserted into the cord's socket. Never alter the plug in any way.
This fixture has been rated for up to (1) 4w max Type T LED bulb (included) or (1)
40w max Type T incandescent bulb (not included). To avoid the risk of fire, do not
exceed the recommended wattage.
WARNINGS:
All wires are connected. When unpacking, be careful not to pull wires, as a
bad connection may result. Do not connect electricity until the sconce is fully
assembled. To reduce the risk of fire, electrical shock, or personal injury,
turn off and unplug lamp and allow it to cool prior to replacing lightbulb.
Do not touch bulb when fixture is turned on or look directly at lit bulb.
Keep flammable materials away from lit bulb.
DO NOT REMOVE THE CARDBOARD INSULATOR SURROUNDING THE SOCKET.
THIS PRODUCT IS NOT A TOY AND HAS NO PLAY VALUE.
TEXTURED METAL SWING-ARM SCONCE – ASSEMBLY INSTRUCTIONS
DIRECT-WIRE ASSEMBLY INSTRUCTIONS:
1. Carefully remove all parts from the box and remove all plastic coverings.
2. SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX / CIRCUIT
BREAKER.
3. Cut the plug from the end of the electrical cord. From the back side of
the fixture, pull the electrical cord through the exit hole at the bottom of
the back plate. Then thread plug screw (D) into the hole vacated by the
cord.
4. Cut the cord to the desired length (at least 6" from the back plate) to make a
"J BOX" connection.
5. Guide the wiring from the outlet box through the center hole in the mounting plate (B).
6. Attach the mounting plate (B) to the outlet box using the mounting plate screws (C) to
secure.
7. Attach the ground wire (usually green or bare wire) from the fixture to the ground
junction box wire from the outlet box (usually green or bare wire). Or wrap the
ground wire around the green ground wire screw (A).
8. Connect the hot wire to the hot junction box wire (usually black) with a wire
connector (G) and wrap the connection with electrical tape. Connect the neutral
wire to the neutral junction box wire (usually white) with a plastic wire connector
(G) and wrap the connection with electrical tape.
9.
Attach the back plate (H) to the mounting plate (B) and use the plate screws (F) to
secure the back plate.
10. Insert (1) LED bulb (I) into the threaded socket.
11.
Adjust the shade with shade joint (K) using arm knob (J) and arm handle (L) to get
the desired angle and height. Follow these steps to adjust the knob:
A.
To adjust the position of the arm, lift up the arm handle to loosen the arm knob.
B.
After loosening the arm knob, adjust the arm to the desired angle, then tighten
the knob. You don't need to tighten the knob with much force; just push the arm
handle down a little to hold the lamp in position.
12. Restore power to the junction box and rotate ON/OFF switch (E) to test fixture.
13. Installation is complete.
CARE INSTRUCTIONS:
To clean, use a soft, dry cloth only.
Do not use polishes or cleaners on the fixture.
