RH Baby&child BELLE UPHOLSTERED CONVERSION CRIB 195 - 36/32 Instructions Manual Download Page 2

Page 2 of 25

BELLE UPHOLSTERED CONVERSION CRIB

Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation. 

Infants can suffocate in gaps between crib sides and a mattress that is too small.

To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless

otherwise advised by your physician.

Strangulation Hazard: 

Strings can cause strangulation! 

DO NOT

 place items with a string around a child's neck, such as hood strings or 

pacifier cords. 

DO NOT

 suspend strings over a crib or attach strings to toys.

To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.

DO NOT place crib near window where cords from blinds or drapes may strangle a child.

Fall Hazard: 

When child is able to pull to a standing position, set mattress to lowest position and remove bumper pads,  large 

toys and other objects that could serve as steps for climbing out.

When child is able to climb out or reaches the height of 35 inches (89cm), the crib shall no longer be used, and 

the child should be placed in a youth or regular bed.

Check this product for damaged hardware, loose joints, missing parts or sharp edges before and after assembly  

and frequently during use. 

DO NOT

 use crib if any parts are missing, damaged or broken. 

Contact customer service at 1-800-762-1751 for replacement parts and instructional literature if needed. 

DO NOT

 substitute parts.

DO NOT

 use a water mattress with this crib.

If refinishing, use a non-toxic finish specified for children's products.

Follow warnings on all products in a crib.

Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.

Infants can suffocate in gaps between crib sides and a mattress that is too small.

  

WARNING:

 Infants can suffocate on soft bedding. Never add a pillow or comforter. Never 

place additional padding under an infant. 

       WARNING: 

Failure to follow these warnings and the assembly instructions could result 

in serious injury or death.

Summary of Contents for BELLE UPHOLSTERED CONVERSION CRIB 195 - 36/32


























Reviews: