RGN 7116L Operating Manual Download Page 6

 

 

14. DO NOT DRIVE FASTENERS CLOSE TO THE EDGE AND CORNER OF THE WORK 
AND THIN MATERIAL 

The work piece is likely to split and the fastener could fly and hit someone. 
 

15. DO NOT DRIVE FASTENERS ON THE TOP OF OTHER FASTENERS. 

Driving fasteners of the top of other fasteners may cause deflection fasteners which could 
cause injury. 
 

16. REMOVING THE FASTENERS AFTER COMPLETING OPERATION 

If fasteners are left in the magazine after the completion of operation, there is the danger of a 
serious accident occurring prior to the resumption of operation, should the tool be handled 
carelessly, or when connecting the air removes all fitting. For this reason, always move the 
fasteners away which remaining in the magazine after completion of the operation. 
 

17. CHECK OPERATION OF THE CONTACT TRIP MECHANISM FREQUENTLY IN CASE 
OF USING A CONTACT TRIP TYPE TOOL 

Do not use the tool if the trip is not working correctly as accidental driving of a fastener may 
result. Do not interfere with the proper operation of the contact trip mechanism. 
 

18. WHEN USING THE TOOL OUTSIDE OR ELEVATED PLACE. 

When fastening roofs or similar slanted surface, start fastening at the lower part and gradually 
work your way up. Fastening backward is dangerous as you may lose your foot place. Secure 
the hose at a point close to the area you are going to driver fasteners. Accidents may be 
caused due to the hose being pulled inadvertently or getting caught. 
 

19. NEVER USE THE TOOL IF ANY PORTION OF THE TOOL CONTROLS (e.g., TRIGGER, 
CONTACT ARM) IS INOPERABLE DISCONNECTED, ALTERED OR NOT WORKING 
PROPERLY. 
 
20.  NEVER ACTUATE THE TOOL INTO FREE SPACE. 

This will avoid any hazard caused by free flying fasteners and excessive strain of the tool.  
 

21.  ALWAYS ASSUME THAT THE TOOL CONTAINS FASTENERS. 
 
22. 

 

DO NOT USE ON  SCAFFOLDINGS LADDERS.

  

The tool shall not be used for specific application for example

 

  When changing one driving location to another involves the use of 

scaffoldings, stairs, ladders, or 

  Ladder alike constructions, e.g. roof laths, 

  Closing boxes or crates, 

  Fitting transportation safety systems e.g. on vehicles and wagons.

Summary of Contents for 7116L













Reviews: