REXROTH Sytronix FcP 5020 Operating Instructions Manual Download Page 13

Page: 13 / 204

1.3.3

Symbols

The following symbols indicate notices which are not safety-relevant but in‐

crease the comprehensibility of the documentation.

Symbol

Meaning

If this information is not observed, the product cannot be used

and/or operated optimally.

•

Single, independent action.

1.
2.
3.

Numbered instruction: The numbers indicate that the actions

must be carried out one after the other.

Tab. 1-2:

Meaning of the symbols

1.3.4

Abbreviations

The following abbreviations are used in this documentation:

Abbreviation

Meaning

FcP system

Frequency controlled pump system

Pressure

Flow rate

Speed

PGF/PGH/PGM

Internal gear pump, constant displacement volume

Rexroth document in English language

Rexroth document in another language

ESD/EMC

Electrostatic discharge/electro-magnetic compatibility

CPU

Central processing unit, processor

EFC

Frequency converter

Displacement of the pump

ASF

Application Specific Firmware, application control software for

EFC frequency converter

Tab. 1-3:

Abbreviations

DOK-SYTROX-FCP5020****-IT01-EN-P

Bosch Rexroth AG

11/201

Frequency-controlled pump drive system Sytronix FcP 5020

About this Documentation

Summary of Contents for Sytronix FcP 5020













































































































































































































Search results

Summary of Contents for Sytronix FcP 5020

Reviews:

Related manuals for Sytronix FcP 5020

Brands by name

Popular brands

REXROTH Sytronix FcP 5020, Operating Instructions Manual

Search results

Summary of Contents for Sytronix FcP 5020

Reviews:

Related manuals for Sytronix FcP 5020

Brands by name

Popular brands