REXROTH Sytronix DRn 5020 Operating Instructions Manual Download Page 127

Page: 127 / 146

14.4

Error Code

14.4.1

Error 1 (OC-1): Overcurrent at Constant Speed

Possible reason

Solution

Sudden load change in run mode

Reduce occurrence and scale of sudden change

Low mains voltage

Check input power supply

Motor power and frequency converter power

do not match

Motor power has to match with frequency converter power

Excessive inertia or load

Check power of motor and frequency converter, check load

The motor cable is too long

● Decrease the carrier frequency (C0.05)
● Use a frequency converter with larger power

Excessive torque compensation

Reduce torque compensation setting (C2.22) till the current decreases

14.4.2

Error 2 (OC-2): Overcurrent during Acceleration

Possible reason

Solution

Excessively short acceleration time

Increase acceleration time (E0.26)

Excessive start-up frequency

Reduce start frequency (E0.36)

Excessive load rotation inertia or impact

Increase acceleration time (E0.26), reduce sudden load change

Running command active while motor is

coasting

Restart after motor stop or start with speed capture (E0.35)

Wrong setting of V/f curve related parame‐

ters

Adjust setting of V/f curve related parameters

Motor power and frequency converter power

do not match

Motor power has to match with frequency converter power

Excessive torque compensation

Reduce torque compensation setting (C2.22) till the current decreases

Wrong motor parameters setting

Correct motor parameters setting

14.4.3

Error 3 (OC-3): Overcurrent during Deceleration

Possible reason

Solution

Excessively short deceleration time

Increase deceleration time (F3.22)

Excessive load rotation inertia

Use suitable brake components. Information about external EFC brake chop‐

pers you can find in R912007235

Motor power and frequency converter power

do not match

Motor power has to match with frequency converter power

Excessive overexcitation braking factor

Reduce [E0.55]

Wrong motor parameter setting

Correct motor parameters setting

DOK-SYTROX-DRN5020****-IT05-EN-P

Bosch Rexroth AG

125/143

Frequency-Controlled Pump Drive System Sytronix DRn 5020

Troubleshooting

Summary of Contents for Sytronix DRn 5020



















































































































































Search results

Summary of Contents for Sytronix DRn 5020

Reviews:

Related manuals for Sytronix DRn 5020

Brands by name

Popular brands

REXROTH Sytronix DRn 5020, Operating Instructions Manual

Search results

Summary of Contents for Sytronix DRn 5020

Reviews:

Related manuals for Sytronix DRn 5020

Brands by name

Popular brands