manualshive.com logo in svg

Rexnord 1874, Engineering Manual

Share
Download
Rexnord 1874 Engineering Manual Download Page 31

ROUND BORE SPROCKETS

Figure 37

Figure 38

SQUARE AND HEX BORE SPROCKETS

Use round bore sprockets on conveyors 
operating at room temperature. When 
installing the sprockets, make sure that all 
sprocket faces are positioned the same way

on the shaft, with identification marks all 
facing the same direction, as shown above. 
After positioning all sprockets in line with 
sprocket tooth pockets in the chain, secure 
the sprockets with set screws. (Also see 
general note below).

Use square or hex bore sprockets on 
conveyors intended for use at elevated or 
lower temperatures (warmers, pasteurizers, 
coolers, etc.). When installing the sprockets 
make sure that all sprocket faces are

positioned the same way on the shaft, with 
identification marks all facing the same 
direction , as shown. Also, be sure to align 
the notched teeth for proper timing.

GENERAL NOTE: It is generally recommended to lock center sprocket(s) to shaft
using set screws or set collars. The other sprockets should be allowed to "float" axially.

SELECTION

PROCEDURE

cont.

Sprocket

Installation

Re
x

®

MatT

op

®

Chains

Rex

®

Engineering Manual                                                                                                                                                         MT-18

Summary of Contents for 1874






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands