background image

 -17 - 

3.

 

Push and hold the Charger Base’s Mute button for 
eight seconds to enter into pairing mode then 
release. 

The LED will be solid RED until pairing is 
complete, as indicated by double flashing RED on 
both the Microphone and the Charger Base (paired 
and muted audio).  If pairing fails at the end of one 
minute on either unit, the LED will flash alternately 
GREEN and RED for a few seconds and turn OFF. 
If this happens, repeat these steps. 

    

Warranty

Warranty

Warranty

Warranty

 

Revolabs, Inc. warrants this product to be free of manufacturing 
defects. Repair or replacement of any defective part or unit (at the 
discretion of the Seller) will be free of charge for the period of 90 
days. 
 
Any attempt by the user to alter the equipment, or equipment 
damaged by negligence, accident, or Acts of God voids this 
warranty. 
 
The Seller shall not be liable for any consequential damage 
resulting from the malfunction of this product. Should the user 
experience unsatisfactory performance from this equipment, 
contact the Seller to obtain instructions for return, or replacement, 
as deemed necessary. 
 
This warranty is not transferable by the original end user. 
 

Revolabs, Inc. 

63 Great Road 

Maynard, MA 01754 

www.revolabs.com

 

1-800-326-1088 

 

 -18 - 

LED Status Indications

LED Status Indications

LED Status Indications

LED Status Indications    

The following LED patterns are shown on either the Microphone or 
the Charger Base. 
 
 

LED pattern 

Meaning 

Solid GREEN 
(Microphone only*) 

Confirmation of power-up or battery 
reaching full charge. * In earlier versions 
LED will turn OFF when fully charged.

 

Solid RED 

Pairing mode, or confirmation of 
powering-down, or battery charging. 

GREEN flash every 
1.5 seconds 

Microphone paired, connected and un-
muted. 

Two RED flashes 
every 1.5 seconds 

Microphone paired, connected and 
muted. 

YELLOW flash 
alternating with 
GREEN flash 

Microphone paired, connected, un-muted 
and battery low. 

YELLOW flash 
alternating with two 
RED flashes 

Microphone paired, connected, muted 
and battery low. 

Alternating RED, 
YELLOW, GREEN, 
YELLOW 
(Microphone only) 

Searching for a connection, or out of radio 
range.  The Microphone will try to re-
establish the link for about 15 minutes, and 
then turn off automatically. The Microphone 
will beep five times every 30 seconds. 

Alternating RED, 
GREEN 

Microphone is not paired to this Base 
Station. 

Rapid RED flashes 
continuing for more 
than a few seconds 

Radio congestion – it is not possible to 
make a radio connection because there 
are already too many nearby users of the 
RF band, or there is heavy radio 
interference.   

Groups of five rapid 
RED flashes 

Unit is faulty.  Please contact your place 
of purchase for advice on return. 

Summary of Contents for xTag 02-DSKSYS-D













Reviews: