GENERAL DESCRIPTION
These Fan Goggle Systems consist of an interchangeable protective lens that locks into the
goggle frame with an adjustable headband and is powered by a single AA battery (included).
Depending upon user conditions, the fan operates in 3 speeds: slow, medium, fast or in
power-off mode if the fan is not required. Depending upon the model that you have received,
there may be additional lenses that all provide 100% UV protection. For example: Clear for
indoor and nocturnal use, Solar for daytime use to cut glare and High-Contrast for low-
light conditions. The adjustable head strap keeps goggles secure during rigorous activity.
Depending on the model you have received an anti-reflective sleeve, microfiber cleaning
pouch/cloth (ideal for cleaning your lenses) and rugged storage case may also be included.
OPTIONAL PRESCRIPTION (RX) CARRIER
If you require corrective lenses, an optional Rx Carrier for prescriptions is available. You can
provide the Rx Carrier to your Optometrist who will insert your prescription lenses into the
Rx Carrier. To order an Rx Carrier visit: www.revisionmilitary.com.
www.revisionmilitary.com
REMOVING THE LENS FROM THE FRAME:
(If using an Rx Carrier, remove the Rx Carrier and Rx Connector prior to removing the lens.)
Grasp the center of the top of the frame with your thumb and forefinger of one hand, and the center bottom
of the frame with the other hand. Pull the frame from the top and bottom, peeling it away from the lens.
Push the lens forward forcefully to release it from the goggle frame.
INSTALLING THE LENS INTO THE FRAME:
Working from the front of the goggles, first insert the right edge of the lens then the left edge into the
corresponding areas in the frame. Continue to work the lens into the frame, working from the outer edges
across the top, around the side and across the bottom, fitting the keyhole notches securely over the posts.
The nosepiece will be the final area which is secured.
When the lens is completely inserted, ensure there are no gaps showing between the lens and the frame.
Clean lens (see below) to remove fingerprints and smudges.
REMOVING/FASTENING THE SIDE-CLIP:
To remove the side-clip:
First remove the lens from the frame. Next, grasp the goggle frame with your thumb and forefinger. Peel
away the side clip from the top of the frame.
NOTE:
There is no reason to remove the side clip except to install or remove the anti-reflective sleeve.
To fasten the side-clip:
Grasp the goggle frame with your thumb and forefinger. Align the grip warts on the bottom of the frame to
the holes on the lower portion of the side clip. Next, align the hole on the top of the frame with the posts on
the side clip and press into place.
OPERATING MODES
There are 3 operating modes indicated on the battery pack housing:
OPEN:
To open the battery pack and add/change the battery.
OFF:
The cap is closed and secured but there is no current transmitted from the battery pack to the electronics.
This position is for storage and when the fan is not required. Note: the fan ships in the “Off” Operational Mode.
ON:
Turns the system on. See below to change the fan speed.
INSTALLING/CHANGING THE BATTERY:
To preserve the life of the battery, the Goggle System is shipped with a new, AA battery which is not pre-installed.
Installing the battery:
First twist the battery pack cap to the “Open” position. A notch on the battery cap lines up to the Open position marking. Remove cap. Insert a new AA battery
into the housing. Polarity is important. The negative end of the battery is inserted into the battery housing while the positive end faces towards the battery cap.
A plus (+) sign is indicated on the cap’s metal contacts. Replace the battery cap, ensuring that the battery cap notch lines up to the “Open” position. Firmly
push the battery cap and housing together while twisting the notch to the desired Operating Mode.
Once installed, the battery has a useful life of 36 hours continuous operation, medium speed – 0° F to 105° F (18° C to 40° C).
Battery may last longer when used in warmer climates.
Changing the battery:
To replace the battery, follow the directions above but replace the old battery with a new, AA battery. Replace the cap as indicated above.
OPERATING THE FAN:
Ensure the Operating Mode is in the “On” position and then use the push button at the right end of the battery pack,
opposite the battery cap, to turn on/off and to switch between fan speeds.
Turning on/off:
Press and hold button until the fan activates.
To switch fan speeds:
Short presses to toggle between the three fan speeds: slow, medium and fast.
Select the appropriate fan speed depending upon user conditions.
To turn the fan off:
Switch the operating mode back to “Off”.
GOGGLE INSTRUCTIONS
FAN INSTRUCTIONS
WEARING OVER HELMET STRAP ADJUSTMENT
To tighten the elastic head strap, move the slider
clip on the strap to the left, adjusting until the
system fits comfortably and snugly against your
face. To loosen, move the slider clip to the right.
CHANGING THE LENS
High-impact goggles require the lens to be
held very securely within the goggle frame for
best performance and for your protection. Do
not be afraid to apply force to the lens and put
pressure on the flexible frame when removing
or inserting the lens. Revision Goggles are built
tough. They can take it.
DESERT LOCUST
®
& ASIAN LOCUST
®
FAN
GOGGLE SYSTEM
USER INSTRUCTIONS
IMPORTANT
© 2016 REVISION MILITARY INC., DESERT LOCUST®, ASIAN LOCUST® AND REVISION® ARE TRADEMARKS OF REVISION MILITARY.
UAE 5-0312-0005 JAN/2016
Battery casing cap with on/off switch
Tri speed with button control
