background image

10

7.) Bend the holding tabs you selected outward.

8.) Set FAN into place in the opening using holding tabs, now the tabs hold the fan 

in position in the ceiling opening.

holding tab 

holding tab 

holding tab 

WARNING:

 Disconnect the AC power before any work is done to any part of 

the circuit ReVent

®

 is connected to. If you do not understand this warning, 

seek the services of a qualified licensed electrician.

WARNING:

 Copper to copper only. Do 

not

 use aluminum wire.

WARNING:

 Follow all local electrical and safety codes, and NEC (National 

Electrical Codes).

CAUTION:

 If your house wires do not match these colors, determine what 

each house wire represents before connecting. You may need to consult a 

qualified licensed electrician to determine this safely.

9.) Disconnect FAN motor from electrical enclosure. Remove the electrical cover 

set screw and slide open the electrical enclosure.

10.) Connect wiring using the provided QUICK CONNECTS (U.S.A.) or WIRE 

NUTS (Canada).

OR

WIRE NUT

Qty:3

(Canada only)

2-WIRE QUICK

CONNECT

Qty:2

(U.S.A. only)

3-WIRE QUICK

CONNECT

Qty:1

(U.S.A. only)

remove set

 screw

unplug fan

 connector

slide

Summary of Contents for RVSH110





























Reviews: