English
English
4 CHARGING THE MODEL
Attention:
The battery and motor must cool down for 15 to 30 minutes before charging
and after every flight. Otherwise they can be damaged. The charging process must
be constantly monitored. Always ensure that the charging process takes place on a
fireproof surface in a fire-resistant environment.
• Plug the USB charger into a USB port with a minimum of 500 mAh power. The battery
must be inserted into the model for charging, although do not switch on the model
4A
.
The status LED on the charger begins to illuminate.
• Insert the plug of the USB charger into the charge connection
1B
on the underside of
the model
4B
. The charger plug should slide gently into the charging socket – DO NOT
USE FORCE. If the plug is not correctly inserted into the charging socket, the battery
may become damaged and, under certain circumstances, cause injury.
• The status LED on the charger goes out when the charging process starts.
• The charging process lasts approx. 40 minutes and must be continuously monitored.
The LED on the charger turns red again up as soon as the charging process is finished.
• Disconnect the USB charger plug from the model after charging.
The model can fly for approx. 5-7 minutes after a charge time of approx.
40 minutes.
Warning notice:
The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
3 INSERTING BATTERIES (REMOTE CONTROL)
3B
Insert 4 x 1.5 V AA batteries
and pay attention to the
polarity specifications, as
indicated in the battery
compartment.
3A
Turn screw
2L
counter-
clockwise and remove
battery compartment
cover
2K
.
3C
Close the battery
compartment cover
and screw the
locking screw
clockwise.
and neighbouring parts, as well as
physical injury!
• Never use a charger for NiCd/NiMH
batteries!
• Always ensure that the charging
process takes place on a fireproof
surface in a fire-resistant environment.
• Do not leave the battery unsupervised
during the charging process.
• Never disassemble or alter the battery
contacts. Do not damage or puncture
the battery cells. There is a risk of
explosion!
• The LiPo battery must be kept out of
reach of children.
• When disposing of batteries, they must
be discharged or their capacity must
be fully depleted. Cover exposed
terminals with adhesive tape in order
to prevent short-circuiting!
Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
• Never allow the remote control and
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
Technical changes and differences in
color reserved!
Required batteries for the model:
Power supply:
Rated output:
1 x DC 3,7 V / 0,9 Wh rechargeable
LiPo battery (included)
Capacity: 250 mAh
Battery requirement for the
remote control:
Power supply:
DC 6 V
Batteries:
4 x 1.5 V “AA”
(included)
Charger:
Power supply: DC 5 V / 500 mA
via USB-Port
Rated output: 4.2 V / up to 500 mA
2 REMOTE CONTROL
2A
Control for thrust and rotation
2B
Control for Forward/Reverse and Banking
2C
Trim for rotation
2D
Trim for forwards/backwards
2E
Trim for sideways
2F
ON/OFF switch
2G
Power LED
2H
Button for Headless Mode
2I
Speed button
2J
Flip function button
2K
Battery compartment cover
2L
Battery compartment locking screw
1 MODEL
1A
ON/OFF switch
1B
Charging connection
1C
Status LED (under each leg)
5 START PREPARATION
The model must be switched on first in order to connect it to the remote control. To do
this, slide
5A
the battery into the model‘s battery compartment, insert the battery plug into
the battery port in the model and close the battery compartment. Do not use force and
make sure that the polarity is correct
5B
. Then switch the ON/OFF switch
1A
on the model
to ON
5C
. The status LED
1C
flashes slowly when switching on. Then place the model on
an even, flat and stable surface.
Before switching on the remote control, the control for thrust and rotation
2A
must
point down. To switch on the remote control, move the ON/OFF switch
2F
to ON and
briefly push the control for thrust and rotation up and then down again. After approx.
3 seconds, the model activates and is ready for use.
Once you have finished flying, switch the model off first and then the remote control.
Unplug the battery from the model and remove the battery from the model.
A A
A A
A A
A A
16
17
