background image

11

Installation and Operation
Blood Bank Refrigerators

13 Optional Accessories

Remote Alarm. Optional for all blood bank models. 

Temperature Recorders

All six inch recorders use pressure-sensitive chart paper 
(1 box @ 50 charts included); no inking is required. Four inch 
recorders use inked marker pens.

Chart Paper

Low Voltage Protection

Casters

Description

Catalog 

No.

Standard Remote Alarm. Provides audible and visual 

signal in the event of temperature rise or power failure. 
Adaptable to telephone switchboard. Can be located 
up to 1/3 mile (1760 ft/536 m) from cabinet. Must be 
used with electronic alarm system and connected to 
normally-open or normally-closed remote alarm 
contacts. Wire not included. Specify voltage when 
ordering.

5612

Deluxe Electronic Remote Alarm System. User 

programmable to sound alarm in the event of 
temperature rise or power failure. Can dial up to four 
telephone numbers to advise of alarm condition 
across any telephone system which accepts pulse 
dialing. One system can monitor up to four individual 
cabinets. In addition, the system can monitor up to 
three groups of cabinets. Contact Revco for detailed 
specifications. Customer installed.

6224

Description

Catalog 

No.

Temperature recorder, 6 in. circular chart, seven-day drive, 

free-standing. Customer installed. Specify voltage 
when ordering.

6383-7

Description

Catalog 

No.

Chart paper, package of 50, for six inch, seven-day 

recorder, -40

°

C to +25

°

C.

6184

Chart paper, package of 50, for four inch, seven-day 

recorder, -40

°

C to +50

°

C.

6198

Description

Catalog 

No.

Voltage Safeguard. Free-standing. Helps protect 

electrical equipment from damage by boosting low 
voltage automatically. Provided with terminal board for 
direct wiring. Field installed. Specify voltage when 
ordering.

5575

Description

Catalog 

No.

Caster Dolly. For use with 5.4 cu.ft and 11.5 cu.ft 

cabinets.

6174

Dual-Wheel Casters. Set of four, 2 in. diameter, for 23.3, 

29.2, and 51.1 cu.ft models only.

6041

Summary of Contents for REB-1204














Reviews: