resideo Protectorelay, Installation Instructions Manual

Page: 2 / 8

R4184D; R8184G,M,N,P PROTECTORELAY® OIL PRIMARY CONTROLS
69-0618—04 2
Fig. 2. Wire and mount 150°F (66°C) maximum ambient
temperature oil primary control.
Line Voltage Wiring Connections
Wiring must comply with all local codes and ordinances.
1. Be sure all line voltage connections are in a wiring
enclosure such as a junction box or the appliance
wiring compartment.
2. Make the line voltage connections as shown in
Fig. 3 through 9.
3. Splice the leads with solderless connectors.
IMPORTANT
Do not exceed the load ratings listed in Table 1.
4. Thread the line voltage cad cell leads through the
hole on the bottom of the low voltage terminal
strip. See Fig. 1 or 2.
Alarm Contact Rating: 25 VA at 24V, 50/60 Hz.
Mounting
1. If necessary, use the control as a template to mark
and drill new mounting holes.
2. Mount the control using no. 8 screws (obtained
locally).
Low Voltage Wiring Connections
After mounting, make low voltage connections to screw
terminals as follows:
• R4184D—connect the cad cell leads to the F-F
terminals. See Fig. 3.
• R8184G—connect the cad cell leads to the F-F
terminals and thermostat leads to the T-T terminals.
See Fig. 4 and 5.
• R8184M—connect the cad cell leads to the F-F
terminals and connect remaining low voltage wiring
as shown in Fig. 6.
NOTE: The Y and G terminals are not connected to the
internal circuitry of the R8184M. The Y and G
terminals are provided to simplify the connec-
tions of the cooling equipment.
• R8184N—connect the cad cell leads to the F1-F2
terminals and thermostat leads to the T1-T2
terminals. See Fig. 7.
• R8184P hydronic hookup. Connect the cad cell leads
to the F-F terminals. See Fig. 6.
• R8184P warm air hookup. Connect the card cell leads
to the F-F terminals and the thermostat leads to the
R-W terminals. See Fig. 9.
Fig. 3. Typical hookup for R4184D.
CAD
CELL LEADS
LINE
VOLTAGE LEADS
MOUNTING
SCREW HOLE
RED RESET
BUTTON
VENTILATION
SLOTS
4 x 4 JUNCTION
BOX
HOLE OR KNOCKOUT FOR
CAD CELL LEADS
LOW VOLTAGE
TERMINAL STRIP
1 STRIP WIRES 3/8 in. (9.5 mm); INSERT FROM SIDE, ABOVE OR BELOW.
ATTACH WITH NO. 8 MOUNTING SCREWS (OBTAINED LOCALLY).
VENTILATION SLOTS ONLY AVAILABLE ON SELECT MODELS.
1
2
2
3
3
M1642C
Table 1. Load relay contact ratings.
Model
120 Vac 240 Vac
AFL ALR AFL ALR
R4184D; R8184G,M,N
(45-second models)
7.4A 44.4A 3.7A 22.2A
R8184P (15-, 30-, 45-
second models)
7.4A 44.4A NA NA
R8184G (15- and
30-second models)
10.0A 60.6A 5.0A 30.0A
JUNCTION BOX
BLACK
ORANGE
WHITE
R2
SAFETY
SWITCH
M715A
POWER SUPPLY. PROVIDE DISCONNECT MEANS
AND OVERLOAD PROTECTION AS REQUIRED.
CAD
CELL
F
F
R4184D PROTECTORELAY CONTROL
SAFETY
SWITCH
HEATER
1K
TRIAC
BILATERAL
SWITCH
CAPACITOR
R1
1K2
1K1
1
1
IGNITION
LIMIT
THERMOSTAT
OIL VALVE
(OPTIONAL)
BURNER
MOTOR
L2
L1
(HOT)
®