manualshive.com logo in svg

Resco 7000 Series, Installation Manual

Share
Download
Resco 7000 Series Installation Manual Download Page 11

Resco Series 7000 Return version. Step-by-step Installation Guide. August 2014

 

11

Step 

20

Step 

21

Clean Panels
Clean all components, including pencil marks 
on the floor and walls.
Sweep floor and remove rubbish.
Wipe down with soapy water.

Resco Limited. 

12 Kahu Crescent 

Te Rapa, Hamilton 3200. New Zealand 

Phone: 0800 800 950, +64 850 1025 

Fax: +64 7 850 1026 

(www.resco.co.nz)

©Resco August 2014

RETURN VERSION

Fix this side as well

Step 

18 

Fix division panels
 

a.  Ensure all division panels line up with the 
bottom of each U-Channel.

 

b. Drill 4 x holes on one side of each 
U-Channel. 

Use 3.5mm drill bit with (D) Stainless 
Steel Pop Rivets 30mm and 600mm from 
the top and the same from the bottom.

Fit hardware.
Line up the coat hook with the pre-drilled holes in 

the doors and screw hook on.
Use (B) 8GA x 12 screws.

Fix the indicator bolt in the pre-drilled position.
Use the supplied M5 x 20 screws.

Hang doors
Lining up the hinges attached to each Stile with the 
predrilled holes on the doors, hang the doors.
Use the supplied (A) 8GA x 12 screws.

Step 

19

Summary of Contents for 7000 Series












Reviews:

No comments

Brands by name

Popular brands

Load more brands