manualshive.com logo in svg

REPLIGEN XCell Lab XC-LAB-D, User Manual

Share
Download
REPLIGEN XCell Lab XC-LAB-D User Manual Download Page 59

 

  

 

XCell™ Lab Controller 

User Guide 

 

 

59          repligen.com           XC-LAB-UG-V4 

Alarm/Interlock 

Event Trigger 

System Response 

Diaphragm Pressure Sensor 

Failure 

Diaphragm pressure sensor (P2) 

analog input is out of range (0-10V) or 

disconnected from the PLC 

If enabled, system will not calculate 

TMP, it is set to 0 

Permeate Pressure Sensor 

Failure 

Permeate pressure sensor (P3) is not 

communicating to the PLC, when it is 

configured to be present 

If enabled, system will not calculate 

TMP, it is set to 0 

PCV not Tracking Setpoint 

The filter is running, but the 

diaphragm pressure sensor (P2) reads 

35 mbar or more below the 

commanded pressure or exhaust 

value for more than 3 consecutive 

cycles 

This alarm can be a demonstration 

of supply deficiencies. If the 

deficiency occurs on the vacuum 

command, the pressure command 

will be locked and not allowed to 

increase. If the alarm occurs due to 

a lack of pressure, the vacuum 

command will be locked and not 

allowed to increase 

Initialization Error 

The initialization process does not 

complete successfully 

Cannot start process when caused 

by inadequate pressure supply, 

when caused by flow sensors, the 

default flow values will be used 

Filter B Flow not Meeting 

Setpoint 

The average flow after 40 consecutive 

cycles is less than 90% of the setpoint 

System adjusts the pressure curve 

to try to attain the setpoint 

PCV not Tracking Setpoint 

The filter is running, but the 

diaphragm pressure sensor (P2) reads 

35 mbar or more below the 

commanded pressure or exhaust 

value for more than 3 consecutive 

cycles 

This alarm can be a demonstration 

of supply deficiencies. If the 

deficiency occurs on the vacuum 

command, the pressure command 

will be locked and not allowed to 

increase. If the alarm occurs due to 

a lack of pressure, the vacuum 

command will be locked and not 

allowed to increase 

Initialization Error 

The initialization process does not 

complete successfully 

Cannot start process when caused 

by inadequate pressure supply, 

when caused by flow sensors, the 

default flow values will be used 

 

 

 

Summary of Contents for XCell Lab XC-LAB-D






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands