Renogy DCDC30 Manual Download Page 16

15

LED Indicators

Operation 

Color

 

Status

 

Description

Red

ON

Bulk charge (MPPT)

Slow Flashing

Boost charge

Color

Status

Description

Color

Status

Description

Color

Status

Description

Solar Charging Indicator

Single Flashing

Float charge

Fast Flashing

Equalizing charge

Double Flashing

Current-limit charge

OFF

Not charging

Red

ON

Alternator is charging the service battery

Slow Flashing

PV is charging the starting battery

Alternator/Charging Indicator

OFF

Not charging

Red

Yellow

Green

ON

Battery Full

ON

Battery voltage normal

Service Battery Indicator

ON

Battery undervoltage

Slow Flashing

Battery over discharged

Fast Flashing

Battery over voltage/ over temperature

Red

Yellow

White

Blue

Green

ON

SLA (Default)

ON

GEL

Battery Type Indicator

ON

FLD

ON

LI

ON

User

NOTE

1. Red to Yellow: When the voltage reaches 12.2V under voltage recovery

2. Yellow to Red: When the voltage drops to 12.0V under voltage warning

3. Yellow to Green: A. When it reaches constant voltage charging state, the charging current is 

smaller than 3A, lasts for 30 seconds; B. When the charging current is higher than 3A, it keeps 

charging until it reaches constant voltage state and the current drops below 3A, lasts 30 seconds.

The Charging Indicator may change under the following conditions:

User mode is an extra feature accessed via App or Monitoring Screen; Future 

Development

NOTE

Summary of Contents for DCDC30

























Reviews: