background image

 

  

Important Safety Instructions 

 

Please save these instructions.

 

This manual contains important installation, operation, and maintenance instructions for the 
Smart  Lithium  Iron  Phosphate  Battery.  Please  observe  these  instructions  and  keep  them 
located near the battery for further reference. The following symbols are used throughout 
the manual to indicate potentially dangerous conditions or important safety information.

Indicates a potentially dangerous condition. Use extreme caution when 
performing this task.

Indicates a critical procedure for the safe and proper installation and 
operation of the battery.

Force majeure including fire, typhoon, flood, earthquake, war, and terrorism.

Intentional or accidental misuse, abuse, neglect or improper maintenance, and use under  
abnormal conditions.

Improper installation, improper operation, and malfunction of a peripheral device.

Please keep the battery away from water, heat sources, sparks, and hazardous chemicals.

DO NOT puncture, drop, crush, burn, penetrate, shake, or strike the battery.

DO NOT open, dismantle, or modify the battery.

Contamination with hazardous substances, diseases, vermin, or radiation.

Alterations to the product without express written consent from the manufacturer.

The manufacturer accepts no liability for any damage caused by:

 

Indicates a procedure or function that is important to the safe and proper 
installation and operation of the battery.

Disclaimer

General Safety Information

Summary of Contents for 50LFP48S





















Reviews: