Operating instructions
Card reader CR03I
Item no. 1170551
Intended use
The product is intended for installation in a 8.9 cm (3.5“) slot of a computer enclosure.
On the front, there is a card reader for reading out / recording cards of different types
and a USB port.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting,
fire, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• Card reader
• Front panel (silver)
• 4 x screws
• Driver CD
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Also observe the safety and operating instructions of any other devices
which are connected to the product.
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Operating elements
1
2
3
8
9
7
6
5
4
1 USB port
2 CF slot
3 MS slot
4
Power
indicator (shines during operation)
5 Card reader indicator
(flashes while reading and recording)
6 Fixing screw
(front panel)
7 SD slot
8 microSD slot
9 XD slot
Driver installation
Insert the driver CD and follow the instructions. In case the CD does not start by itself,
manually open the file with the name “setup.exe” on the CD.
Installation
When in doubt about how to install the device correctly, please contact an
expert or a specialist workshop and let them carry out the installation.
In case of improper installation, the product as well as your computer and
all connected devices will be damaged.
Lethal Danger!
Switch off the computer in which the product is to be installed and all
connected devices and separate all devices from the mains voltage.
Unplug the mains plug! To switch the device off via the ON/OFF switch is
not enough!
• Open the housing of your computer and carefully take off the lid of the housing.
• Look for a free 8.9 cm (3.5“) installation slot and remove the respective front cover.
There may be a metal shield behind it which needs to be removed. For some housings
it can be screwed off, for some it has to be carefully broken out. Depending on the
housing the complete front cover of the housing has to be removed beforehand.
• Push the panel in the 8.9 cm (3.5“) plug-in unit of your computer housing; firmly
screw the panel afterwards.
• Connect the cables of the panel with the corresponding connections of your
mainboard. In doing so, pay attention to the information in the mainboard
manufacturer’s instructions.
• Lay the cables in a way so that they cannot get into a fan of the PC, to fasten them
use, e.g. cable fasteners (not included).
• Close the computer case.
• Connect your computer and monitor with the mains voltage und switch on all
devices.
• If your computer does not start correctly, switch it off immediately and check all
settings and cable connections.
Replacing the front panel
Remove the device from the computer’s housing and disconnect it from the
power supply before replacing the front panel.
• Unscrew both screws at the side of the device and carefully remove the front panel.
• Carefully pull the two LEDs from the front panel.
• Slide the two LEDs carefully into the respective openings of the other front panel
(green = Power / red = Access).
• Mount the other front panel with care and fasten it with the two screws.
