•
Ensure that no underfloor cables or wires are damaged during drilling/screwing. Accidentally
drilling into electrical cables can cause a fatal electric shock!
• Always pay attention to your safety when working with electrical tools (such as a drill).
Refer to the safety information in the corresponding instructions.
• Ensure that no unauthorized persons are present in the assembly area when mounting the
product.
Assembly
The following instructions are designed to be used in combination with the images in the manufacturer's
instructions.
Figure 1
Place the connecting piece (F) onto the pole (C) and then insert the bracket (D) into the connecting piece.
Figure 2
• Screw the bracket (D) to the connecting piece (F) and the pole (C) using the two M6 screws (H). Use the
hex key (K) to tighten the screws.
• Guide the charging cable for your tablet through the pole.
Figure 3
Carefully remove the three protective caps on the base.
Figure 4
• Guide the charging cable through the opening on the base, and then pull it to one side.
• Place the pole onto the base and secure it in place by tightening the four socket screws (G) with the hex
key (K).
Figures 5a & 5b
• Decide where you want to mount the stand. Mark the positions of the drill holes on the mounting surface.
Use the base (B) as a template.
a) If you are mounting the stand on a wooden surface, drill the necessary holes.
b) If you are mounting the stand on a concrete, stone, or tiled floor, drill the necessary holes and then
insert the concrete anchors (J).
•
Secure the base to the floor using the three ST5.5x38 screws (L). Before inserting the screws, place the
washers (M) on top of the holes. The non-slip plastic feet should face downwards.
Figure 6
Carefully replace the three protective caps on the base, ensuring that they click into place.
Figure 7
• Unlock the cylinder lock and remove the key.
• Carefully remove the protective frame from the plastic case (loosen at the edges and then remove).
• Remove the plastic pads from the parts of the case that you want to screw to the bracket. This will depend
on whether you want to attach the case in portrait or landscape orientation. Use a screwdriver to remove
the plastic pads (push up from underneath and then lift the pads out of the case).
Figures 8a & 8b
• Screw the plastic case (A) to the bracket (D) on the pole using the four M5x2 screws (I). Tighten the screws
using a suitable Phillips screwdriver (not included).
• The plastic case can be attached in portrait or landscape orientation as desired. Figures 8a and 8b show
the plastic case in portrait and landscape orientation.
• Replace the plastic pads once you have screwed the plastic case to the bracket and the pole.
Figure 9
• Place a suitable tablet into the plastic case (A).
• Insert the protective frame (insert the bottom of the frame and then press down on the sides until it clicks
into place).
• Insert the key into the lock and turn it anticlockwise to lock the frame in place.
• To unlock the frame, insert the key into the lock and turn it clockwise.
Maintenance and cleaning
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these could damage the
casing or even impair the functioning of the product.
• Use a dry, lint-free cloth to clean the product.
Technical data
Load capacity .....................................1 kg
Tablet dimensions (W x H x D) ........... (158 to 182 mm) x (7.6 to 10.5 mm) x (221 to 255 mm)
(plastic case suitable for VESA 75 x 75)
Operating/storage conditions ..............-30 to +80 °C, 1 – 80 % relative humidity (non-condensing)
Base dimensions (W x H x D) .............368 x 1131 x 277 mm
Weight ................................................2.14 kg
Operating instructions
Universal floor stand for 9.7 - 10.1 inch tablets
Item no. 1483526
Intended use
This height-adjustable stand is designed for tablets with a display size of 24.6 cm (9.7") to 25.7 cm (10.1").
It consists of an elegant aluminium pole with a built-in cable guide on the back and a sturdy steel base.
The stand comes with a protective frame that locks your tablet in place to protect it against theft. The frame
can only be removed using the keys provided. The angle of the bracket can be adjusted.
This product is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms,
must be avoided under all circumstances. For safety reasons, you must not rebuild and/or modify this
product. If you use the product for purposes other than those described above, the product may be damaged.
Read the instructions carefully and keep them. Make this product available to third parties only together with
its operating instructions.
Delivery content
• Plastic case
• 4 x M5x12 screws
• Base
• 3 x concrete anchors
• Pole
• 3 x ST5.5x38 screws
• Bracket
• 3 x washers (Ø 5 mm)
• Connecting piece
• 5 mm hex key
• 2 x keys
• Operating instructions
• 4 x M6x16 screws
• Manufacturer's instructions
• 2 x M6x8 screws
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR
code above. Follow the instructions on the website.
Explanation of symbols
The symbol with the exclamation mark in the triangle is used to highlight
important information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
a)
General information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing
material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity
and moisture.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• Consult an expert when in doubt about the operation, safety or assembly of the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
b) Assembly
• Check the contents of the packaging before assembling the product. You will not be able to
assemble the product unless all components are present.
• Assembling the product in an unsuitable location can result in injury or damage to property!
• Proceed with care when assembling and mounting the product! This product has some sharp
edges which have the potential to cause injury!
• Only carry out the work necessary to mount the product. Never attempt to modify or repair
the product.
• Work on a clean, soft and dry surface. Protect valuable furniture using a suitable pad or cloth.
• Do not overtighten the screws, as this may damage the threads and reduce the strength of
the fitting.
• Ensure that the charging cable will not become trapped in between the pole and the bracket.
•
Check that all the screw fittings are secure from time to time. The screws may become loose
over time as the product is moved around.
• Do not overload the stand. Refer to the technical data for information on the load capacity. Do
not hold onto the tablet stand or use it to support yourself. Do not secure any objects to the
tablet stand other than a tablet.
• If you are in any doubt about how to assemble the product, ask a technician to assemble it
for you.
•
Do not attach the stand to unsuitable floor surfaces. Thin or laminate flooring is normally
unsuitable. However, special parts are sometimes available for these types of surfaces. If in
doubt, contact a specialist before assembling the product.
• Mounting materials (such as screws and dowels) may vary depending on the mounting
surface. The dowels and screws that are included with the product are only suitable for
solid floors. Special dowels and screws are not included and must be purchased separately
depending on your floor type.
• Plan the mounting location carefully so that the tablet stand will be located in the desired
position once you have finished mounting it.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2016 by Conrad Electronic SE.
*1483526_v1_0916_02_DS_m_(1)_4L
