Renesas RX200 Series, User Manual

Page: 24 / 41

Renesas Solution Starter Kit for RX23W 6. Configuration
R20UT4446EG0102 Rev. 1.02 Page 24 of 41
Jun 22, 20
6.3 E1/E2 Lite Debugger Configuration
Table 6-2 below details the function of the option links associated with E1/E2 Lite Debugger Configuration.
Table 6-2: E1/E2 Lite Debugger Configuration Option Links
Signal
name
MCU MCU Peripheral Selection Destination Selection
Pi
n
Po
rt
Signal Fit DNF
Interface
/Function
Fit DNF
P26 B2 P26
PMOD1-MOSI J7 (2-3pin short), R204 R62, R73, R205 PMOD1.2 - -
EMU-TXD J7 (2-3pin short), R62 R204, R73, R205 E1.5 - -
SSIRXD0 J7 (2-3pin short), R73 R204, R62, R205 P26 - -
SERIAL-TXD J7 (2-3pin short), R205 R204, R62, R73 U8.2 - R203
USB0-VBUSEN J7 (1-2pin short) - U5.4 - -
P30 A2 P30
PMOD1-MISO J6 (2-3pin short) R76, R80, R209 PMOD1.3 - -
SW2 J6 (1-2pin short) R76, R80, R209 SW2 - -
EMU-RXD R76 J6 (open), R80, R209 E1.11 - -
AUDIO_MCLK R80 J6 (open), R76, R209 P30 - -
SERIAL-RXD R209 J6 (open), R76, R80 U10. 2 - R208
PC7 F1 PC7
EMU-UB
- -
E1.10 - -
DSW-UB SW3.2 - -
PC7 - - PC7 - -
SERIAL-TXD R203 - U8.2
J7 (1-2pin
short)
-
RESn B6 -
EMU-RESn - - E1.13 - -
SW-RESn
- -
RES(Switch) - -
MD_FINED B7 -
EMU-MD_FINED - - E1.7 - -
DSW-MD_FINED
- -
SW3.1 - -
6.4 Power Supply Configuration
Table 6-3 below details the function of the option links associated with Power Supply Configuration.
Table 6-3: Power Supply Configuration Option Links
Reference Configuration Fit DNF Related Links
USB0_2 Connect 5V Power rail to VBUS0.
J3 (2-3 short),
J5 (1-2 short)
- U6.1, U6.2
USBCN0 Connect 5V Power rail to FT234_5V.
J3 (1-2 short),
J5 (1-2 short)
- U6.1, U6.2
USB_5V Connect 5V power rail to USB_5V . R57 - U5.2, U5.3
U6 Output Connect U6 Output power rail to Board_VCC. J13 (short) - -
Board_5V Connect 5V power rail to Board_5V. - - U3.8, U6.1, U6.2
Board_VCC Connect Board_VCC power rail to UC_VCC. - - E1.8, U3.8
UC_VCC
Connect Board_VCC power rail to UC_VCC. J10 (short) - U1
Enable current probe for measurement MCU
current consumption.
- J10 (open) U1
VBATT
Connect UC_VCC power rail to VBATT. R133 R134 U1
J11 *1 connected to VBATT of MCU
.
R134 R133 U1
*1
: J11 is a power connector for VBATT, not a jumper. Do not short-circuit J11 Pin 1 and Pin 2 because the
power supply is directly connected to ground.
Table 6-4
below details the function of the jumpers associated with the Power Supply Configuration.
Table 6-4: Power Supply Configuration Jumper Settings
Reference Jumper Position Configuration Related Links.
J10
Short Connect Board_VCC power rail to UC_VCC. -
Open
Enable current probe for measurement MCU current consumption.
-
J13
Short Enable U6 Output power. -
Open
Disable U6 Output power.
-
J3
1-2 Short Enable USBCN0(FT234_5V). -
2-3 Short Enable USB0_2(VBUS0). J5 (1-2 short)
All open Disable USBCN0(FT234_5V), USB0_2(VBUS0). -