manualshive.com logo in svg

Renesas RX Series, User Manual

Introducing the artisan RX Series Instruction Manual, an essential resource for getting the most out of your artisan RX product. Easily download this comprehensive manual for free from manualshive.com, providing you with detailed instructions and guidance for seamless usage and optimum performance.

Share
Download
background image

R01UH0823EJ0100 Rev.1.00

Page 1397 of 1823

Jul 31, 2019

RX23W Group

38. Serial Peripheral Interface (RSPIa)

38.3.10.2

Slave Mode Operation

(1) Starting a Serial Transfer

If the SPCMD0.CPHA bit is 0, when detecting an SSLA0 input signal assertion, the RSPI needs to start driving valid 
data to the MISOA output signal. For this reason, when the CPHA bit is 0, the assertion of the SSLA0 input signal 
triggers the start of a serial transfer.
If the CPHA bit is 1, when detecting the first RSPCKA edge in an SSLA0 signal asserted condition, the RSPI needs to 
start driving valid data to the MISOA output signal. For this reason, when the CPHA bit is 1, the first RSPCKA edge in 
an SSLA0 signal asserted condition triggers the start of a serial transfer.
When detecting the start of a serial transfer in a condition in which the shift register is empty, the RSPI changes the status 
of the shift register to “full”, so that data cannot be copied from the transmit buffer to the shift register when serial 
transfer is in progress. If the shift register was full before the serial transfer started, the RSPI leaves the status of the shift 
register unchanged, in the full state.
Irrespective of the CPHA bit setting, the timing at which the RSPI starts driving of the MISOA output signal is the 
SSLA0 signal assertion timing. The data which is output by the RSPI is either valid or invalid, depending on the CPHA 
bit setting.
For details on the RSPI transfer format, refer to 

section 38.3.5, Transfer Format

. The polarity of the SSLA0 input 

signal depends on the setting of the SSLP.SSL0P bit.

(2) Terminating a Serial Transfer

Irrespective of the SPCMD0.CPHA bit, the RSPI terminates the serial transfer after detecting an RSPCKA edge 
corresponding to the final sampling timing. When free space is available in the receive buffer (the SPRF flag is 0), upon 
termination of serial transfer the RSPI copies received data from the shift register to the receive buffer of the SPDR 
register. Upon termination of a serial transfer the RSPI changes the status of the shift register to “empty”, regardless of 
the receive buffer state. A mode fault error occurs if the RSPI detects an SSLA0 input signal negation from the beginning 
of serial transfer to the end of serial transfer (refer to 

section 38.3.8, Error Detection

).

The final sampling timing changes depending on the bit length of transfer data. In slave mode, the RSPI data length 
depends on the SPCMD0.SPB[3:0] bit setting. The polarity of the SSLA0 input signal depends on the SSLP.SSL0P bit 
setting.
For details on the RSPI transfer format, refer to 

section 38.3.5, Transfer Format

.

(3) Notes on Single-Slave Operations

If the SPCMD0.CPHA bit is 0, the RSPI starts serial transfers when it detects the assertion edge for an SSLA0 input 
signal. In the type of configuration shown in 

Figure 38.7

 as an example, if the RSPI is used in single-slave mode, the 

SSLA0 signal is fixed at the active state. Therefore, when the CPHA bit is set to 0, the RSPI cannot correctly start a serial 
transfer. To correctly execute transmit/receive operations by the RSPI in slave mode in a configuration in which the 
SSLA0 input signal is fixed at the active state, the CPHA bit should be set to 1. If there is a need for setting the CPHA bit 
to 0, the SSLA0 input signal should not be fixed.

Summary of Contents for RX Series
































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RX Series

Panasonic WJ-NV200K Quick Reference Manual preview
WJ-NV200K
Brand: Panasonic Pages: 4
IEI Technology PCIE-Q470 Quick Installation Manual preview
PCIE-Q470
Brand: IEI Technology Pages: 19
IEI Technology KINO-DH420 User Manual preview
KINO-DH420
Brand: IEI Technology Pages: 87
IEI Technology HPE-4S2 Quick Installation Manual preview
HPE-4S2
Brand: IEI Technology Pages: 3
Ratoc Systems SCSI PC Card REX-9530V Product Manual preview
SCSI PC Card REX-9530V
Brand: Ratoc Systems Pages: 30
Dahua Smart 1U Quick Start Manual preview
Smart 1U
Brand: Dahua Pages: 24
RadiSys EPC-31 Hardware Reference Manual preview
EPC-31
Brand: RadiSys Pages: 44
Behringer EXPANSION CARD X-DANTE Quick Start Manual preview
EXPANSION CARD X-DANTE
Brand: Behringer Pages: 65
Barco ImagePRO-HD Installation Manual preview
ImagePRO-HD
Brand: Barco Pages: 121
Renesas Emulator MCU Board for 38D5 Group M38D59T-RLFS User Manual preview
Emulator MCU Board for 38D5 Group M38D59T-RLFS
Brand: Renesas Pages: 4
TANDBERG D5018501 Hardware User Manual preview
D5018501
Brand: TANDBERG Pages: 3
Qlogic Storage Networking (Unified Fabric Pilot) Installation Manual preview
Storage Networking (Unified Fabric Pilot)
Brand: Qlogic Pages: 76
IDT Tsi310TM User Manual preview
Tsi310TM
Brand: IDT Pages: 207
ETAS BR-XETK-S4.0 User Manual preview
BR-XETK-S4.0
Brand: ETAS Pages: 82
Crystal Vision TANDEM HD-21 User Manual preview
TANDEM HD-21
Brand: Crystal Vision Pages: 54
G&D DL-DVI-Vision-IP Series Installation And Operation Manual preview
DL-DVI-Vision-IP Series
Brand: G&D Pages: 228
Cypress Semiconductor CY62136EV30 MoBL Specification Sheet preview
CY62136EV30 MoBL
Brand: Cypress Semiconductor Pages: 12
Promise Technology FastTrak TX4000 User Manual preview
FastTrak TX4000
Brand: Promise Technology Pages: 76

Brands by name

Popular brands

Load more brands