Renesas CE2000-H8S Series User Manual Download Page 31

Page: 31 / 96

Figure 2-14

End of Programming

•

Restart the emulator.

Note:

1. Make sure that there is

no interruption

during the programming. Otherwise, reprogramming

will not be possible and user will need to send the emulator back for the upgrade work.

2. The

programming

of the emulator Logic will

fail if the SODIMM is attached

3. User can perform the upgrade at any time by executing the

CE Programmer.exe

if necessary.

2.5 Installation

Details

The installer creates the following icons in the program group:

Figure 2-15

HEW Start up Menu

These menu have the following functions:
“High-performance Embedded Workshop 3”

: HEW will be activated.

“CE2000 User Manual ”

: User manual for CE2000

“CE2000 Read Me”

: Read Me file for CE2000

www.DataSheet4U.com

Summary of Contents for CE2000-H8S Series

































































































Search results

Summary of Contents for CE2000-H8S Series

Reviews:

Related manuals for CE2000-H8S Series

Brands by name

Popular brands

Renesas CE2000-H8S Series, User Manual

Search results

Summary of Contents for CE2000-H8S Series

Reviews:

Related manuals for CE2000-H8S Series

Brands by name

Popular brands