background image

5

Description

Warranty

The warranty conditions are listed in the 
"General terms and conditions".  
Please contact your contractual partner  
in the first instance.

Environmental pro-

tection and recycling

Disposing of packaging

All products are packed for transport 
in environmentally friendly materials. 
You can make a valuable contribution 
to reducing waste and sustaining raw 
materials by only disposing of packaging 
at approved collection points. 

Disposal of  
components

The manufacturing process for the 
units is subject to continuous qual-

ity control. Only high-grade materials are 
processed, the majority of which 
are recyclable. You can also  
contribute to environmental protec-
tion by only disposing of components 
in accordance with local regulations and 
in an environmentally safe manner, e.g. 
through authorised disposal and recycling 
specialists or at collection 
points.

The fresh water station was developed 

for use by regenerative heating appli-

ances, particularly for heat pumps. It can 

supply one to two residential units with 

fresh domestic hot water.

The domestic hot water is only heated 

when there is demand, via a stainless 

steel plate heat exchanger, in a hygienic 

flow process. 

The energy supply required for this is 

provided as needed by a heating water 

storage tank.  

When the hot tap is opened, the in-

tegrated circulation pump is switched 

on by a flow switch and heating water 

is conveyed from the heating water 

storage tank to the primary side of the 

stainless steel plate heat exchanger, 

causing the cold drinking water flowing 

Intended use 

The fresh water station was developed 

for use by regenerative heating appli-

ances, particularly for heat pumps. 

The domestic hot water is only heated 

when there is demand, via a stainless 

steel plate heat exchanger, in a hygienic 

flow process. 

The energy supply required for this is 

provided as needed by a heating water 

storage tank.SFlbAny alternative or ad-

ditional use is classed as non-intended 

use. The manufacturer/supplier assumes 

no liability for damages arising from such 

use. The user bears the sole risk in such 

cases.

Intended use also includes working in ac-

cordance with the operating manual and 

installation instructions and complying 

with the maintenance requirements.

Summary of Contents for BG 1000

















Reviews: