Before using read the important safety
instruction section in front of the manual.
Charging
Your new Smooth&Silky® Titanium should
be charged for 24 hours before it can be
used for the first time. It can be charged in
the cleaning base or by plugging the cord
into the shaver directly.
Preparing the System
Adding the cleaning solution:
1.
Press the latch buttons on the sides
of the cleaning base and lift off the top
section. You will
need to keep the
buttons pressed in
as you lift.
2.
The cleaning solu-
tion tank is in the
bottom section.
Remove the filter
from the tank and
set aside.
3.
Pour the bottle of
cleaning solution
into the base of the
unit through the
opening where the
filter was removed.
Fill the tank to the
bottom of the fill
tab.
4.
Return the filter
back to its original
position.
NOTE:
It is important to make sure the filter
is in place to keep the unit operating
properly. The filter collects hair clippings
and debris that could permanently clog the
system and render it inoperable. Make sure
to replace the filter whenever you replace
the cleaning solution.
5.
Return the top section of the cleaning
base by lining up the three tall posts
with the three holes in the tank. Push
down the top until the two latches click
into place.
6.
You can dispose of the cleaning solution
bottle and cap with your normal trash, or
recycle where local ordinances apply.
Operating the
Charging/Cleaning System
Plug the power cord into the cleaning base
and then into an electrical outlet.
Remove the shaver’s clear plastic head
guard and place the shaver into the unit,
head side down. Push the shaver down and
slide its “tail” toward the “neck” of the
base until it clicks into place.
Charging
Your shaver automatically
begins to recharge as soon
as it clicks into place in
the cleaning base. While it
is charging, the green indi-
cator light will flash; when
it is fully charged the
green light will stop blink-
ing and glow steadily.
1
2
3
How to Use
8
9
Cleaning
To activate cleaning mode, simply press the
CLEAN button on the cleaning base. The
yellow indicator light flashes through the
entire cleaning cycle, which lasts approxi-
mately 25 minutes. When the cleaning
cycle has been completed, the yellow light
will stop blinking and glow steadily. The
unit then returns to charging mode.
!
Wait until the cleaning cycle has finished
before removing the shaver from the base.
If the shaver is removed during the clean-
ing cycle it will be covered with the special
cleaning/lubricating solution and will be
unusable.
Solution levels
The cleaning solution will slowly evaporate
with use. When the solution levels get low,
the red replacement indicator light will
begin to flash. This means you have
enough cleaning solution left for approxi-
mately 5 more cleanings. If the red light
stops blinking and glows steadily, the unit
will not operate until the solution and filter
have been replaced.
Replacing the Filter and Solution
Remington® cleaning solution and filters
were specially designed for the WDF-
7000CS. The cleaning solution contains a
high percentage of alcohol and a special oil
that lubricates your shaver each time it is
cleaned. The filter is specially designed to
collect hair debris to keep solution clean.
To refill the cleaning solution and replace
the filter, follow the steps for "Preparing the
System" above. But before replacing the
top of the unit, rinse out the tank with fresh
water and allow it to air dry to remove any
sediment.
Wipe off the base periodically with a damp
cloth and remove any hair debris that has
collected where the shaver sits.
!
To avoid damage to the cleaning system,
use only Remington® special cleaning
solution. The Remington® replacement
solution and filter, model #CC-100, is sold
at many major retailers and online at
www.remington-products.com. It can also
be ordered by phone at 800-736-4648 in
the U.S. or 800-268-0425 in Canada.
To Charge Your Shaver
(out of cleaning base)
The WDF-7000CS can also be recharged
by plugging the cord into the shaver
directly.
■
Make sure your shaver is turned off.
■
Use only the charging adapter supplied
with the shaver.
■
Connect the cord to the shaver, then
plug the charging adapter into the
electrical outlet. The shaver’s charging
indicator will light.
■
Your shaver cannot be overcharged, so
you can leave it plugged in and charging
between shaves.
■
To preserve the life of the batteries, let
them fully run out every six months,
then recharge them for a full 24 hours.
NOTE:
If your shaver battery is completely
discharged or the shaver has not been
used for a long time, charge the shaver
for approximately one to two hours before
shaving. After done charge for 16 hours
for full charge.
WDF-7000_IB 8/28/06 9:59 AM Page 8
