Contains a
listed adaptor
Before you begin:
■
Wait at least 15 minutes after
getting up before shaving, to
ensure the face is free of
puffiness that may be present
from sleeping. (Diagram D)
■
Make sure your face is clean
and dry before starting.
(Diagram E)
■
Always use a clean, dry shaver.
(Diagram F)
To shave
Push the ON/OFF button. Hold the shaver so both foils touch your face at the same time.
(Diagram G) This allows the shaver to work the way it was designed for the closest shave
and minimum wear. Avoid holding the shaver at an angle so only one screen touches the
skin at a time. This will distort the screen and could cause skin irritation.
Shave with short, circular strokes. Use your free hand to stretch your skin. This
encourages your whiskers to stand out, making it easier for them to enter the cutting
chamber. (Diagram H)
Never press hard. Pressing only flattens your whiskers, making it harder for them to
enter the cutting chamber. It will also wear out the cutting surface more quickly.
(Diagram I)
D
Cleaning Your Shaver
Remington
®
recommends cleaning your
shaver after every use for optimal
performance.
1.
Turn shaver OFF.
2.
Remove the head assembly by squeezing
on both release buttons and pulling up from the body of the shaver.
3.
Screens-
Do not use the brush to clean the screens. Instead, blow the shavings out
or rinse the screens under cold or warm water.
4. Cutters and trimmer-
Use the cleaning brush to sweep any loose hairs from
the cutters and trimmers, or rinse/dunk them in cold or warm water. Do NOT use
hot water.
5.
After cleaning, return the foils and head assembly to their
original position on the shaver.
6.
If the shaver was rinsed with water hold it facing downward
into the sink, and turn it on for a few seconds to dispel
additional water. A gentle shake will also help.
7.
To clean the external surfaces of the shaver, use a damp
cloth. Do NOT use strong detergents or other chemicals.
8.
To dry, wipe the surface of the overall shaver with a dry
towel. Do NOT use a hair dryer or heater to dry the shaver.
Screens and Cutters
To assure smooth, efficient performance, it is important to
clean your shaver.
Daily
Blow out the stubble after each shave.
1.
Turn the shaver off.
2.
Remove the head assembly by squeezing on both release buttons
and pulling up from the body of the shaver. (Diagram M)
3.
Thoroughly blow out the stubble from the screen and cutters.
4.
Replace head assembly.
Weekly
Brush out the cutters and trimmer at least once a week.
1.
Turn the shaver off.
2.
Remove the head assembly by squeezing on both release buttons and pulling up
from the body of the shaver.
3.
Use the cleaning brush to sweep out the cutters and trimmer. DO NOT USE THE
CLEANING BRUSH ON THE SCREENS. Damage may occur to the holes in the screens.
4.
Replace head assembly. Remington
®
Shaver Saver
®
Lubricant (SP-4) lubricates and
cleans your shaver's cutters and head assembly. The lubricant helps remove hair
clippings while reducing wear. A quick spray after each shave keeps your shaver
operating at peak performance.
Cleaning Cautions
■
Shaver can be placed under running water for cleaning only.
■
Do not use an aggressive cleansing agent as this may destroy the shaver coatings.
■
Do not remove or replace the head assembly while shaver is running as it may cause
damage to the unit's screens or cutters.
■
Replace worn or damaged parts with Remington
®
replacement parts only.
Trimmer Care
Cleaning
1.
Turn the shaver off.
2.
Extend the trimmer to its maximum height by pressing the right trimmer button.
3.
Use the cleaning brush to sweep off any clippings that may have accumulated
around the trimmer assembly. Using the supplied brush will enable you to get into
the area between the trimmer and the shaver.
Lubricating
1.
Every six months apply a drop of light machine oil one-third and two-thirds of the
way along the blade.
2.
Using your fingertip, spread the oil along the teeth.
3.
Run the trimmer for a few seconds to distribute oil.
Replacing Cutters and Screens
To prevent inadvertent damage to the cutters and screens, do not attempt to remove
them from the head assembly unless you are replacing them. Removal instructions are
included with the cutter and screen replacement packages.
To replace a cutter assembly that is removed unintentionally:
1.
Hold the assembly in the middle of the "T".
2.
Gently slide the plastic portion of the cutter assembly over the top
of the oscillator tip. (Diagram N)
3.
Do not push downward on the ends of the cutters, as you may
bend the cutter, reducing its ability to operate smoothly.
4.
Do not remove cutters from the plastic pieces they are attached to, as you may
damage the assembly.
Questions or comments:
Call 800-736-4648 in U.S.
Or visit
www.remington-products.com
100-240 VAC 50/60 Hz
® Registered Trademark of Spectrum Brands, Inc., or one of its subsidiaries.
© 2008 SBI
08/06 Job #CS36186
Dist. by: Spectrum Brands, Inc., Madison, WI 53711
800-736-4648
MADE IN CHINA
T22-26432
E
F
G
H
I
Cleaning and Maintenance
Because they are subject to daily use, the cutters and screens of your shaver will
wear and eventually require replacement to maintain a close, comfortable shave. It is
very important to replace your screens and cutters when necessary to ensure a close,
comfortable shave without irritation.
Depending on your shaving technique and habits, the screens will usually last 6 months;
the cutters, 12 months. If you are replacing the cutters, it’s a good idea to replace the
screens at the same time.
Here are some signs that your foils and cutters need replacing:
Irritation:
As screens get worn, you may notice that your skin feels more sensitive
after a shave, particularly when you apply aftershave.
Pulling:
As cutters wear, your shave may not feel as close and you may feel your
shaver is pulling at your whiskers.
Wear-through:
You may notice that the cutters have worn through the screens.
The replacement part for this shaver is model SP-95 (screens) and SP-96 (screens
and cutters).
U.S. residents: To order shaver accessories call 800-231-8793, visit
www.remington-products.com, or visit your local retailer.
Disposal
1
2
3
4
5
Battery Removal
When your rechargeable shaver reaches the end of its useful life, the batteries must
be removed from the shaver and be recycled or disposed of properly in accordance
with your state and local requirements. If this is not required by law, you may elect to
dispose of the shaver without removing the batteries.
THE FOLLOWING PROCEDURE SHOULD BE FOLLOWED FOR BATTERY REMOVAL:
!
Make sure shaver is unplugged before you begin, to avoid a possible electric
shock hazard.
1.
Press the two side buttons and pull off the shaver head assembly.
2.
Remove the 4 outer screws from inside the shaver head. Loosen the top assembly from
the body.
J
K
L
N
M
Performance Guarantee
Operating the Pop-up Mini-foil
Your shaver is equipped with a 2-position mini-foil. Use the mini-foil push tab to extend
or retract the mini foil.
1.
Completely retracted (down), the mini-foil works with the 2 large screens to provide
a close and comfortable shave.
2.
Fully extended (up), the mini-foil can be used to provide a close shave for small or
difficult-to-reach areas, for a detailed look.
!
Do NOT retract the mini-foil by pressing down directly on the screen. This could
permanently damage the screen.
Adjusting to your new shaver
As with every shaver, your shave will improve over time. So allow about three weeks to
develop an effective shaving style and for your beard to adjust to the new shaver. The
adaptation period may take a little longer if your skin is sensitive, or if you alternate
between shaving methods.
To help smooth the transition to your new shaver, a special lubricant has been applied
to the shaver’s screens and cutters. The lubricant looks like fine white or gray powder,
and disappears with use.
This shaving appliance
is a washable shaver,
the hand-held part of
which may be cleaned
under water.
3.
Remove the screw from the back of the shaver near the power port.
4.
Remove the two side panels to allow removal of 2 more screws.
5.
Pry off the back cover of the shaver, starting at the gap below the shaver socket.
6.
Cut or break the wires attached to the battery on the right.
7.
Pry both of the batteries loose from the foam adhesive tape on the PCB.
8.
Cut or break the wires connecting the batteries to the PC board.
CAUTION:
DO NOT PUT IN FIRE OR MUTILATE YOUR BATTERIES WHEN DISPOSING AS
THEY MAY BURST OR RELEASE TOXIC MATERIALS. DO NOT SHORT CIRCUIT AS IT MAY
CAUSE BURNS. DISPOSE PROPERLY IN ACCORDANCE WITH YOUR LOCAL AND STATE
REQUIREMENTS.
Limited Two-Year Warranty
Spectrum Brands, Inc. warrants this product against any defects that are due to faulty
material or workmanship for a two-year period from the original date of consumer
purchase. This warranty does not include damage to the product resulting from
accident or misuse.
If the product should become defective within the warranty period, we will repair
it or elect to replace it free of charge. Return your product and sales receipt with
your name, address and day time phone number to: Spectrum Brands, Inc. , Attention:
Consumer Services, 601 Rayovac Drive, Madison, WI 53711. For more information call
800-736-4648 in the US or 800-268-0425 in Canada.
Warranty excludes:
■
Screens and cutters
KEEP ORIGINAL SALES RECEIPT AS PROOF OF PURCHASE FOR WARRANTY
PURPOSES.
This warranty does not cover products damaged by the following:
■
Accident, misuse, abuse or alteration of the product
■
Servicing by unauthorized persons
■
Use with unauthorized accessories
■
Connecting it to incorrect current and voltage
■
Wrapping cord around appliance causing premature wear & breakage
■
Any other conditions beyond our control
SPECTRUM BRANDS, INC. SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
PRODUCT. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO IM PLIED
WARRANTIES OF FITNESS AND MERCHANTABILITY, ARE LIMITED IN DURATION TO
TWO YEARS FROM DATE OF ORIGINAL PURCHASE.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state or province to province. Some states do not allow the
exclusion or limitation of incidental, special or consequential damages.
Performance Guarantee
Spectrum Brands, Inc. Money-back Offer
If within 30 days after you have purchased your Remington
®
branded product, you
are not satisfied and would like a refund, return it with the sales slip indicating
purchase price and date of purchase to the retailer from whom it was purchased.
Spectrum Brands, Inc. will reimburse all retailers who accept the product within
30 days from the date of purchase. If you have any questions concerning the money-
back guarantee, please call 800-736-4648 in the US or 800-268-0425 in Canada.
36186_MS_6000_IBA.indd 2
6/17/08 4:18:47 PM
