Reliance HS 7000 Installation And  Operating Instructions, Owners Manual Download Page 9

AUTO
RETURN

BACK
RECLINE

BACK

RAISE

LIFT
DOWN

UP

LIFT

FIGURE 3

Footswitch Operation 

REMARQUE

 : Les interrupteurs RAISE (LEVER) et 

LOWER (BAISSER) la base sur l’interrupteur au pied 

sont programmables. Selon la conception initiale, 

le mouvement de la chaise S’ARRÊTE lorsque l’un 

ou l’autre de ces interrupteurs est relâché. Si vous 

désirez que le mouvement de la chaise CONTINUE, 

après que l’un ou l’autre de ces interrupteurs est 

relâché, consultez la section 4 pour connaître les 

instructions de programmation.

3.3.  Chair Top

3.3.1.  An electric motor supplies power for the movement 

of the chair top.

3.3.2.  Raising & Reclining the Chair Top with 

Membrane Switches.

•  The chair top may be raised or reclined by Membrane 

Switches on either side of the chair back (Figure 2).

•  To  lower,  depress  the  triangle-shaped  DOWN  arrow 

located BELOW the “TOP”. This is called the LOWER TOP 

or RECLINE switch. 

•  To raise the chair top from these switches, depress the 

triangle-shaped UP arrow located ABOVE the next “TOP”. 

This is called the RAISE TOP switch.

NOTE: 

 The RAISE and LOWER/RECLINE switches 

on the Chair Back are programmable. By design, 

the motion of the Chair will CONTINUE when either 

of these switches is released. If you want the motion 

of the Chair to STOP after either of these switches 

is released, then see Section 4 for programming 

instructions.

REMARQUE

 : Les interrupteurs RAISE (LEVER) 

et  LOWER/RECLINE  (BAISSER/INCLINER)  sur 

le  dossier  de  la  chaise  sont  programmables. 

Selon la conception initiale, le mouvement de la 

chaise  CONTINUE  lorsque  l’un  ou  l’autre  de  ces 

interrupteurs  est  relâché.  Si  vous  désirez  que 

le  mouvement  de  la  chaise  S’ARRÊTE,  après 

que  l’un  ou  l’autre  de  ces  interrupteurs  est 

relâché, consultez la section 4 pour connaître les 

instructions de programmation.

CAUTION - 

ANY chair movement that 

CONTINUES after the switch is released may 

be stopped by depressing the STOP switch 

or by depressing the same switch a second 

time.

PRÉCAUTION : 

TOUT mouvement de la 

chaise qui CONTINUE après que l’interrupteur 

est relâché peut être arrêté en appuyant sur 

l’interrupteur STOP (ARRÊT) ou en pressant le 

même interrupteur une seconde fois.

3.3.3.  Raising & Lowering the Chair Top From the 

Footswitch.

•  For operation from the footswitch (Figure 3), depress 

the right side of the left-hand pedal to raise the chair 

top.

•  Depress the left side of the left-hand pedal to lower/

recline the chair top.

NOTE:  

the RAISE and LOWER/RECLINE switches 

on  the  footswitch  are  also  programmable.  The 

motion of the chair will STOP when either of these 

switches is released. If you want the motion of the 

chair to CONTINUE after either of these switches 

is released, then see Section 4 for programming 

instructions.

IN-7000

9

Summary of Contents for HS 7000

















































Reviews: