WARNING AND OPERATING INSTRUCTIONS
FOR USING THE LOAD MOMENT INDICATOR (AML-L)
1. When operating crane on outriggers:
When a load is lifted in the front position and then
Set P.T.O. switch to "ON".
swung to the side area, make sure the value of the
Press the outrigger mode select key to register for the
LOAD MOMENT INDICATOR (AML-L) is below the
outrigger operation. Press the set key, then the
360
o
lifting capacity.
outrigger mode indicative symbol changes from
(2) For creep operation :
flickering to lighting.
The creep capacities are attainable only when boom
Press the boom mode select key to register the boom
is in the straight forward position of chassis and the
mode, then the boom mode indicative symbol changes
over front position symbol is on. If boom is not in the
from lighting to flickering. Each time the boom mode
straight forward position of chassis, never lift load.
select key is pressed, the mode changes. Press the set
3. A swing dose not automatically stop even if the crane
key to select the status that corresponds to the actual
becomes overloaded.
state of the boom, then the boom mode indicative
4. During crane operation, make sure that the displays on
symbol changes from flickering to lighting.
front panel are in accordance with actual operating
When erecting and stowing jib, select the status of jib
conditions.
set (jib state indicative symbol flicker).
5. The displayed values of LOAD MOMENT INDICATOR
2. When operating crane on rubber:
(AML-L) are based on freely suspended loads and
Set P.T.O. switch to "ON".
make no allowance for such factors as the effect of
Press the on-tire mode select key. The on-tire mode
wind, sudden stopping of loads, supporting surface
indicative symbol comes on. Each time the on-tire
conditions, inflation of tire, operating speed, side loads,
mode select key is pressed, the mode changes.
etc. For safe operation, it is recommended when
Select the creep operation, the on-tire mode
extending and lowering boom or swinging, lifting loads
indicative symbol flicker.
shall be appropriately reduced.
Press the boom mode select key to register the boom
6. LOAD MOMENT INDICATOR (AML-L) is intended as
mode.
an aid to the operator. Under no condition should it be
However, pay attention to the following :
relied upon to replace use of capacity charts and
(1) For stationary operation :
operating instructions. Sole reliance upon LOAD
The front capacities are attainable only when the over
MOMENT INDICATOR (AML-L) aids in place of good
front position symbol comes on. When the boom is
operating practice can cause an accident. The operator
more than 2 degrees from centered over front of
must exercise caution to assure safety.
chassis, 360
o
capacities are in effect.
TR-500XL-3 Axle weight distribution chart
Basic standard machine includes:
34.8'~ 110.6' (10.6 m ~ 33.7 m) 4-section boom
32.2', 56.1'(9.8 m, 17.1 m) 2-stage jib
Main hoist with 623' (190 m) of 3/4" (19 mm)
diameter wire rope
Auxiliary hoist with 361' (110 m) of 3/4" (19 mm)
diameter wire rope
50 ton (45.4 metric ton) hook block
6.2 ton (5.6 metric ton) hook ball
Auxiliary lifting sheave (single top)
Mitsubishi 6D16-TLEA engine
29.5-25-22PR(OR) tires
Remove: 1. 32.2', 56.1' (9.8 m, 17.1 m) 2-stage jib
-3,740
+1,540
-,1000
-1,697
+697
2. 50 ton (45.4 metric ton) hook block
-1,760
+810
-431
-799
+368
3. 6.2 ton (5.6 metric ton) hook ball
+144
-474
-150
+65
-215
4. Auxiliary lifting sheave (single top)
-348
+220
-58
-158
+100
5. 29.5-25-22PR (OR) tires
-3,495
-3,495
-3,172
-1,586
-1,586
-330
-128
Kilograms
-6,990
GVW
Front
Rear
Pounds
GVW
Front
45,690
88,200
-2,200
-950
Rear
19,280
20,720
40,000
42,510
10
C R A N E S E R V I C E
(909) 222-0202 www.reliablecraneservice.com 260 North Smith Ave. Corona, CA 92880