Relectronic CDH 75 M User Manual Download Page 29 | Manualshive

Page: 29 / 56

background image

Printed in the Federal Republic of Germany



TR-Electronic GmbH 2012, All Rights Reserved

05/30/2018

TR - ECE - BA - GB - 0095 - 19

Page 29 of 56

5.1.2.1 MRP protocol support, series 75 / 115

In the GSDML file versions 2.x are always contained two Device Access Points
(DAP´s).

1. DAP without support of the MRP protocol:

CD_75_-EPN V2.x

2. DAP with support of the MRP protocol:

CD_75_-EPN MRP V2.x

“Legacy devices”

Measuring systems > MAC-address 00-03-12-EF-84-28 generally support no MRP
protocol and must be configured under DAP

CD_75_-EPN V2.x

.

“New devices”

Measuring systems

≤ MAC-address 00-03-12-EF-84-28 generally support the MRP

protocol and must be configured under DAP

CD_75_-EPN MRP V2.x

.

In case of replacement, legacy device against new device, the measuring system may
be configured also under the DAP

CD_75_-EPN V2.x

.

«
...
27
28
29
30
31
...
»

Summary of Contents for CDH 75 M

























































Reviews:

No comments

Related manuals for CDH 75 M

Brand: Watt Drive Pages: 54

Brand: a-TroniX Pages: 92

Brand: IRiver Pages: 33

Brand: L-Card Pages: 73

Brand: Lumantek Pages: 14

Brand: MAGIRA Pages: 58

Brand: Wavecrest Pages: 39

Brand: TBM Pages: 6

Brand: D&H Pages: 106

Brand: TANDBERG Pages: 196

Brand: Sabrent Pages: 7

Brand: TR-Electronic Pages: 37

Brand: Solax Pages: 3

Brand: Epever Pages: 24

Brand: Larco Pages: 11

HOME NERATOR SYSTEM 12000 WATT

Brand: GE Pages: 80

Brand: Siko Pages: 36

Brand: CTC Union Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands