Reisinger s4000 Operating Manual Download Page 12

Parameter 51:

Special functions: special input SO

0 – no function

1 – input (NO contact) SO activated  – emergency opening in case of interlocking; door 

OPENS

 and 

remains in this position, until SI is deactivated. This opening of the door is indicated by an acous-
tic signal.

2 – input (NO contact) SO activated  – opening in case of key lock time being active (P88 / P89)

3 – input (NO contact) SO activated – all current functions are interrupted and the door closes

4 – input (NC contact) SO activated – interlocking is deactivated. 

PERMANENTLY OPEN

 function 

will change to partial opening

5 – input (NC contact) SO activated – Pull and go is deactivated; all current functions are interrupted 

and the door closes

6 – input (NO contact) SO activated – door opens and remains in this position, until SI is deactivated

7 – input (NC contact) SO activated – door opens and remains in this position, until SI is deactivated

8 – input (push-button function) SO activated – Door interlocks automatically, on repeated triggering 

the door unlocks again. This function is only active if the door is closed.

Parameter 53:

Summer mode / winter mode

0 – Summer mode, total opening width
1 – Winter mode, reduced opening width at xx% (P54).

Parameter 54:

Opening width for winter mode in %

Parameter 55:

Closing time

0 – normal mode
1 – closing time mode, motion sensor Outside is deactivated 

Parameter 57:

Automatic electrical lock

0 – deactivated
1 – active

Parameter 58:

Interlock K1 as NO contact (0) or NC contact (1). K1 is activated at each opening of the door.

Parameter 59:

1 – after reversing door remains in open position until time (parameter 5) has elapsed

0 – after reversing door remains in open position until a key is pressed

Parameter 60:

Status display

Parameter 61:

Program selector

0 – deactivated
1 – active

Parameter 62:

All parameters are reset back to factory settings; after reset 

carry out teach-in run!

Parameter 63

Lighting effect display frame 

0 – deactivated
1 – activated

Parameter 64 

Default and maintenance message via output AUX

1 – output AUX indicates a default message or maintenance is due
0 – deactivated

Parameter 65:

Audio signal

0 – deactivated
1 – active

Parameter 66:

Power-operated holding in OPEN and CLOSE limit position

0 – deactivated
1 – active motor
2 – active with magnetic break

Parameter 70

Lock time closing time 1:

start 

(Motion sensor Outside is locked)

Parameter 71

Lock time closing time 1:

end   

(Motion sensor Outside is activated)

Parameter 72

Lock time closing time 2:

start 

(Motion sensor Outside is locked)

Parameter 73

Lock time closing time 2:

end  

(Motion sensor Outside is activated)

Parameter 74

Lock time closing time 3:

start 

(Motion sensor Outside is locked)

Parameter 75

Lock time closing time 3

end

(Motion sensor Outside is activated)

– 12 –

Summary of Contents for s4000





















Reviews: