Reiner jetStamp graphic 970 Operating Manua Download

Page: 87 / 94

Technical Data and Accessories

ERNST REINER GmbH & Co. KG

Technical Data and Accessories

Rating Plate

Technical data

Transport and disposal

Accessories

8.1

Rating Plate

Observe the rating plate before the device is connected.

The rating plate is located on the bottom of the device.
The following information has the following meaning:

Mod.

= Model

S/N

= Serial Number

QC.

= Quality Control

jetStamp graphic

970 has the CE-mark according to the currently valid low-voltage and

EMC directive.

jetStamp graphic

970 is in accordance with the following standards or standardized

documents FCC 47 CFR Ch.1 Part 15 Bluetooth: FCC: R7TAMB2300.

= Safety of Information Technology Equipment.

jetStamp graphic

970 is produced according to the safety standards IEC/EN 60950-1.

= Do not point the

jetStamp graphic

970’s nozzles towards the face of persons!

Electrical and electronic waste devices

Waste devices must not be disposed of in the conventional household waste. They must
be returned to a special collection point for recycling of electrical and electronic devices.

Summary of Contents for jetStamp graphic 970































































































Search results

Summary of Contents for jetStamp graphic 970

Reviews:

Related manuals for jetStamp graphic 970

Brands by name

Popular brands

Reiner jetStamp graphic 970, Operating Manua

Search results

Summary of Contents for jetStamp graphic 970

Reviews:

Related manuals for jetStamp graphic 970

Brands by name

Popular brands